SpringerOpen Newsletter

Receive periodic news and updates relating to SpringerOpen.

This article is part of the series Porous Semiconductors - Science and Technology 2012.

Open Access Nano Express

Enhanced photoluminescence of porous silicon nanoparticles coated by bioresorbable polymers

Maxim B Gongalsky1, Alexander Yu Kharin1, Liubov A Osminkina1, Victor Yu Timoshenko1*, Jinyoung Jeong23, Han Lee23 and Bong Hyun Chung23

Author affiliations

1 Physics Department, Lomonosov Moscow State University, Leninskie Gory 1, Moscow, 119991, Russia

2 Major in Nanobioengineering, University of Science and Technology, Daejeon, 305-806, South Korea

3 BioNanotechnology Research Center, Korea Research Institute of Bioscience and Biotechnology, 125 Gwahangno Yuseong, Daejeon, 305-806, South Korea

For all author emails, please log on.

Citation and License

Nanoscale Research Letters 2012, 7:446  doi:10.1186/1556-276X-7-446

The electronic version of this article is the complete one and can be found online at: http://www.nanoscalereslett.com/content/7/1/446


Received:15 May 2012
Accepted:11 July 2012
Published:8 August 2012

© 2012 Timoshenko et al.; licensee Springer.

This is an Open Access article distributed under the terms of the Creative Commons Attribution License (http://creativecommons.org/licenses/by/2.0), which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

Abstract

A significant enhancement of the photoluminescence (PL) efficiency is observed for aqueous suspensions of porous silicon nanoparticles (PSiNPs) coated by bioresorbable polymers, i.e., polylactic-co-glycolic acid (PLGA) and polyvinyl alcohol (PVA). PSiNPs with average size about 100 nm prepared by mechanical grinding of electrochemically etched porous silicon were dispersed in water to prepare the stable suspension. The inner hydrophobic PLGA layer prevents the PSiNPs from the dissolution in water, while the outer PVA layer makes the PSiNPs hydrophilic. The PL quantum yield of PLGA/PVA-coated PSiNPs was found to increase by three times for 2 weeks of the storage in water. The observed effect is explained by taking into account both suppression of the dissolution of PSiNPs in water and a process of the passivation of nonradiative defects in PSiNPs. The obtained results are interesting in view of the potential applications of PSiNPs in bioimaging.

Keywords:
Silicon nanoparticles; Porous silicon; Bioimaging; Polymer coating; Photoluminescence

Background

Optical techniques such as luminescent labeling are widely used in biomedicine today. They are noninvasive and can be employed for in vitro and in vivo diagnostics. One example is in vitro tests on infectious diseases based on a photoluminescence (PL) response, e.g., Gram staining [1]. Another example is the optical coherent tomography, which is successfully employed to detect malignant tumors in vivo[2]. In this case the cost of a single analysis is several times lower than that of radiology treatment. The next field of optical diagnostics is the fluorescent labeling of antibodies in order to estimate efficiency of targeted chemotherapy in vivo[3]. The dendrite cells were tracked by combining the fluorescent labeling with magnetic resonant imaging [4]. In the latter work, fluorescent indocyanine green and magnetic iron oxides embedded into polylactic-co-glycolic acid (PLGA) nanoparticles were used for high resolution diagnostics of lymph nodes. The employed PLGA is a well-known biocompatible polymer for drug delivery applications [5].

Porous silicon (PSi) is known to be potentially applicable in biomedicine [6]. Luminescent PSi consists of a network of silicon nanocrystals (nc-Si) with typical sizes of 2 to 5 nm separated by nanometer-sized pores [7]. The origin of PL is assumed to be the radiative recombination of charge carriers, i.e., electrons and holes coupled in excitons in nc-Si [8]. The quantum confinement for change carriers in nc-Si leads to a significant rise of the PL intensity and spectral shift. Thus, despite that the band gap in bulk crystalline silicon (c-Si) corresponds to the emission wavelength lying in the infrared spectral range, nc-Si can emit PL in the visible range [6,7]. The PL quantum yield of individual nc-Si could be as high as 60% [9]. Note that nc-Si are not only potential PL labels, but they can also be used for photodynamic therapy [10-12].

Quantum dots like CdSe or ZnS could also be used for bioimaging applications [13], but their cytotoxicity is rather high in comparison to nc-Si [14]. Long term biocompatibility is also present due to bioresorbable properties of nc-Si. The dissolution rate of nc-Si in aqueous solution depends on the pH level (acidity or alkalinity) and varies from 1 nm/day to 1 μm/day [15].

There are some reports about successful bioimaging by nc-Si both in vitro[16] and in vivo[17]. The PL properties of colloidal Si-based nanoparticles were demonstrated to exhibit degradation versus time because of dissolution in water [16]. In order to prevent this effect, one needs to use a specific surface coverage. First of all, this coverage should be bioresorbable in order to maintain the bioresorbability of the whole nanoparticles. Secondly, the coverage should protect nc-Si from agglomeration and should stabilize nc-Si-based suspension.

For example, in [18] authors report on in vivo imaging of sentinel lymph nodes by using luminescent nc-Si obtained by laser decomposition of silane. They used carboxylation of nc-Si surface followed by conjugation with specific biomolecules. The prepared nc-Si possessed efficient PL for several hours. Note that the carboxylation does not drastically change the PL intensity and spectral shape inherent for nc-Si. Another case is amine- or methyl-terminated nc-Si described in [19,20]. The organic groups that are covalently bound to the silicon surface induce a blue shift of the PL peak position. Furthermore, the amine- or methyl-terminated nc-Si is characterized by PL lifetimes in the range of nanoseconds, which are significantly shorter than that for uncovered nc-Si. Authors in [18,19] also reported about a significant increase of the PL quantum yield. These results indicate the great potential of an organic coverage for the modification of PL properties of nc-Si. Another interesting approach is based on microplasma treatment of PSi nanoparticles (PSiNPs) in a mixture of water and ethanol [21]. Free radicals created by the plasma decomposition of ethanol molecules lead to alcoxide-based coating of PSiNPs, and the formed coating stabilized the PL properties of PSiNPs. In [22] H-terminated nc-Si, obtained by partial dissolution of thermally treated silicon suboxide, were covered by solid lipids and were used for labeling of human breast cells in vitro. While the structural properties of the prepared nanoparticles were well-controlled, their PL intensity was rather low. Similar results have been recently demonstrated by using uncoated PSiNPs [23].

The present paper is aimed to study PSiNPs coated by biocompatible and biodegradable polymers as PLGA and polyvinyl alcohol (PVA) for bioimaging application. The PLGA/PVA compound is well-known amphiphilic coverage, because PVA strongly binds to PLGA by van der Waals forces [24]. Our results demonstrate that PLGA/PVA-coated PSiNPs possess the efficient PL for longtime storage in water.

Methods

PSi films were prepared by electrochemical etching of boron-doped (100) c-Si wafers (specific resistivity of 1…10 Ohm*cm) in a mixture of HF (48%):C2H5OH (1:1) under etching current density 60 mA/cm2 for 40 min. The etching was done in a Teflon cell with a platinum counter electrode at room temperature.

In order to obtain free-standing PSi films, a short pulse of the etching current approximately 600 mA/cm2 was applied. The free-standing films were rinsed in deionized water and dried in air.

The porosity of the films was measured about 60% ± 5% by using the gravimetric analysis and low temperature nitrogen adsorption Brunauer-Emmet-Teller (BET) method. The BET method allowed us to estimate the mean diameter of pores equal to 4 ± 1 nm.

The dried films were hand-milled in agate mallet for 15 min to get powder. The prepared powder consisted of small individual PSiNPs (sizes of 10 to 200 nm) and larger particles (sizes above 200 nm) detected by using transmission electron microscopy (not shown).

The prepared powder was covered by PLGA/PVA in the following way. At the first step, the powder was mixed with dimethyl sulfoxide (DMSO) to obtain a suspension with particle concentration approximately 1 mg/ml. Then the suspension was centrifuged for 3 min at 2,000 rpm (rotor's radius approximately 40 cm) in order to remove largest particles. The supernatant was ultrasonicated for 4 h in order to form the stable suspension. At the second step, 1 ml of the suspension was mixed with 40 mg of PLGA, and the mixture was stirred for 1 h. Poly(D,L-lactide-co-glycolide) (PLGA, MW:5, 000 Da) was purchased from Boehringer Ingelheim Inc (Ridgefield, CT, USA). Polyvinyl alcohol (PVA, MW:20,000 Da) and DMSO were obtained from Sigma-Aldrich Corporation (St. Louis, MO, USA).

In the third step, the suspension of PLGA-coated PSiNPs (1 ml) was mixed with 9 ml of aqueous solution of PVA (45 mg/ml). Then the suspension of PLGA/PVA-coated PSiNPs was stirred for 20 h in order to create a hydrophilic coverage of PSiNPs and to prevent their agglomeration. At the final step, the nanoparticles were triply precipitated by centrifugation (3,000 rpm, 15 min) followed by washing and stirring in distilled water to remove excessive DMSO and to form aqueous suspensions of PLGA/PVA-coated PSiNPs.

For comparison we have prepared and studied a suspension of uncoated PSi particles by using the powder of as-prepared PSi films mixed with water. Prior to the investigation, the formed suspensions were subjected to ultrasonication for 15 min.

Some parts of the aqueous suspension were used to deposit the nanoparticles on flat surface of c-Si wafer. The dried samples were investigated by means of scanning electron microscopy (FE-SEM, Sirion, FEI Company, Hillsboro, OR, USA) at an acceleration voltage of 10 kV. Additionally, the samples were studied using a Fourier-transform infrared (FTIR) spectrometer (Alpha-P, Bruker Corporation, Billerica, MA, USA) with attenuated total reflectance mode.

The PL spectra of the aqueous suspensions of PSiNPs were measured using a spectrophotometer Perkin Elmer LS-55 (PerkinElmer Inc., Waltham, MA, USA) under continuous wave excitation by a Xe lamp (with excitation wavelength of 350 nm and spectral width of 10 nm).

The PL relaxation transients were detected by R928 photomultiplier tube (Hamamatsu Photonics, Hamamatsu, Shizuoka, Japan) under pulsed laser irradiation by a nitrogen laser (excitation wavelength of 337 nm and pulse duration of 10 ns). The time response of the detection system was better than 1 μs.

The PL quantum yield was measured by comparing the PL intensity and absorption of the samples and a solution of Rhodamine 6 G with the PL quantum yield of about 100%.

Results and discussion

Samples characterization

Figure 1 shows a typical SEM image of the dried uncoated PSiNPs deposited on c-Si substrate. One can see both relatively big particles with sizes up to 4 μm and smaller ones with diameter less than 200 nm (see size distribution in the inset of Figure 1).

thumbnailFigure 1. SEM images of uncoated nanoparticles after ultrasonic treatment. Inset shows size (diameter) distribution of PSiNPs deposited on c-Si substrate.

The polymer coating changes the size distribution of PSiNPs in comparison with uncoated ones. Figure 2 shows that there are no big particles with sizes above 2 μm. The size distribution of the coated PSiNPs has a maximum size at approximately 200 nm (see the inset of Figure 2). The latter value is larger than that for uncoated PSiNPs. The observed modification of the size distribution can be explained by an influence of the PLGA/PVA shell, which stimulates agglomeration of smaller PSiNPs.

thumbnailFigure 2. SEM images of coated nanoparticles after ultrasonic treatment. Inset shows size (diameter) distribution of PSiNPs.

The FTIR spectra of the dried samples were measured in order to determine the chemical composition of the PSiNP surfaces (see Figure 3). The uncoated samples exhibit spectra with dominant absorption peaks at 640 cm-1 and approximately 2,100 cm-1, which correspond to the Si-H wagging and Si-Hx (x = 1,2,3) stretching modes, respectively [25]. Note that the hydrogen-passivated surface is typical for PSi obtained by electrochemical etching in HF solutions [6,24]. Additionally, two peaks at 1,050 cm−1 and at 450 cm−1 related to the Si-O stretching and rocking modes, respectively, point to the partial oxidation of PSiNP surfaces. The storage for 2 weeks of uncoated PSiNPs in water significantly increased the absorption intensity of Si-O bonds and suppressed its absorption by (Si3-)Si-H bonds, which probably transformed into (SixOy-)Si-H bonds. The detection of (SixOy-)Si-H bonds was hampered by their smaller intensity of the absorbance. Dotted line in Figure 3 shows the FTIR spectra of PLGA/PVA-coated PSiNPs. New peak at approximately 1,750 cm−1 is related to the C = O bond [26], and it is indicative for PLGA molecules [27]. On the one hand, the comparable intensities of the Si-O peaks for the uncoated and coated samples evidence the limited oxidation of PSiNPs surface during the coating procedure. On the other hand, the absence of (Si3-)Si-H bond absorption points to the strong losses of hydrogen from the PSiNP surfaces. This effect can be related to the treatment in DMSO.

thumbnailFigure 3. FTIR absorption spectra of the samples: uncoated sample before storage in water (solid line), uncoated sample after storage in water (dashed line) and PLGA/PVA-coated sample after storage in water (dotted line). The storage was done in darkness for 2 weeks at room temperature.

Enhancement of photoluminescence efficiency

Both suspensions of uncoated and coated PSiNPs just after preparation possessed efficient PL under irradiation with the ultraviolet (UV) light (see inset of Figure 4). The PL intensities of the two samples were close to each other at the beginning of the storage. Initially, the PL quantum yield was estimated to be about 5% for both samples.

thumbnailFigure 4. Examples of PL spectra. PL spectra of uncoated (blue line) and coated (red line) samples before (solid lines) and after (dashed lines) 4 days storage. Inset shows photograph of aqueous suspensions of coated and uncoated PSiNPs under UV irradiation just after the preparation.

Stability of the PL intensity of PSiNPs is a key point for bioimaging application. Figure 4 shows PL spectra of the uncoated (blue curves) and coated (red curves) PSiNPs just after formation of suspensions (solid lines) and after 4 days storage (dashed lines). The time dependences of the spectrally integrated PL intensities were measured for both uncoated (squares) and coated (triangles) samples (see Figure 5). The integrated PL intensity of uncoated PSiNPs decreases during storage in water, while the form of the spectrum maintains approximately the same. The PL degradation of PSiNPs can be related to photostimulated reactions with molecular oxygen, which results in the formation of silicon dangling bonds [7,28,29]. In the present work, we intentionally used short illumination time (approximately 1 min) and low intensities (approximately 1 mW/cm−2) of the excitation in order to minimize the possible effects of photostimulated reactions. So, the main reason of the PL degradation of PSiNPs is expected to be the formation of Si dangling bonds because of the dissolution of PSiNPs in water [17]. It is known that the dangling bonds are responsible for the nonradiative recombination of charge carriers in nc-Si with the recombination rate inversely proportional to the nc-Si diameter [30]. Since the PL spectral shape does not change along the degradation process, one can assume that the dissolution instantly quenches nc-Si. The resulted PL spectrum of PSiNPs is a superposition of the contribution of nc-Si which are not subjected to the dissolution.

thumbnailFigure 5. Time dependences of the integrated PL intensity of the samples: uncoated PSiNPs (blue triangles) and coated PSiNPs (red squares). Solid lines are results of nonlinear fitting by Equations 1 and 2, respectively.

Liquid water can penetrate into oxidized parts of the pores of uncoated samples during the storage (sketched in Figure 6 b). Water turns the surface of uncoated PSiNPs from hydrophobic to hydrophilic. New areas of hydrophilic surface allow further water penetration into the pores. This penetration results in the formation of new dangling bonds on the nc-Si surface.

thumbnailFigure 6. Sketch of the samples. (a) A schematic view of the porous Si nanoparticle (PSiNP) coating process where brown color corresponds to silicon, violet to PLGA, green to PVA and light blue to water. Note that every PSiNP includes several smaller nanocrystals (nc-Si). (b) Magnification of the uncoated PSiNP surface contiguous to liquid water. Hydrophobic surface mostly consisted of Si-H bonds was colored black and hydrophilic one mostly consisted of Si-O bonds was colored yellow. (c) Magnification of the coated PSiNP surface. Violet and green lines correspond to PLGA and PVA molecules. Note that liquid water is not in direct contact with the silicon surface of PSiNPs due to the hydrophobic properties of PLGA.

A tendency is opposite in the case of coated PSiNP (see squares in Figure 5). The PL intensity increases due to the passivation of non-radiative defects by water molecules in a gas phase. Water vapors are known to perform good passivation of the dangling bonds [29]. We suppose that coated PSiNPs are protected from the interaction with the liquid phase of water by hydrophobic PLGA layer. On one hand, the enhancement of PL takes place due to the interaction with water vapors present in pores of SiNPs (see Figure 6 c). On the other hand, the PVA coating provides the hydrophilic properties of PSiNPs. The PL properties of coated PSiNPs become stable after 1 month of storage due to the saturation of described process.

The time dependence of the PL intensity of uncoated PSiNPs is well fitted by the following formulae (plotted by blue curve in Figure 5):

<a onClick="popup('http://www.nanoscalereslett.com/content/7/1/446/mathml/M1','MathML',630,470);return false;" target="_blank" href="http://www.nanoscalereslett.com/content/7/1/446/mathml/M1">View MathML</a>

(1)

where is I the initial PL intensity, t is the characteristic time of PL degradation, Ires is the residual PL intensity. The time dependence of the PL intensity of coated PSiNPs is well fitted by the following function (plotted by red curve in Figure 5):

<a onClick="popup('http://www.nanoscalereslett.com/content/7/1/446/mathml/M2','MathML',630,470);return false;" target="_blank" href="http://www.nanoscalereslett.com/content/7/1/446/mathml/M2">View MathML</a>

(2)

where te is the characteristic time of PL enhancement, Irec is the PL intensity of nc-Si with defects, which are able to be passivated during storage in water.

By fitting the experimental data with Equations 1 and 2, one can obtain the values of td and te to be about 2.5 and 5 days, respectively. The obtained Ires is about 20 times smaller than the final PL intensity of coated PSiNPs (I0+ Irec). According to our measurements, the PL quantum yield of coated PSiNPs increased from about 5% to 20% during the storage and it was stable for the next month and afterwards.

Photoluminescence transients

The PL transients provide additional information about the mechanisms of the charge carrier recombination. Figure 7 shows the PL transients of both uncoated (red triangles) and coated (blue squares) PSiNPs. The PL was detected at the maximum position of the corresponding spectra (600 nm). Supposing only the radiative way of charge carrier recombination the PL transients would follow the monoexponential law as follows:

<a onClick="popup('http://www.nanoscalereslett.com/content/7/1/446/mathml/M3','MathML',630,470);return false;" target="_blank" href="http://www.nanoscalereslett.com/content/7/1/446/mathml/M3">View MathML</a>

(3)

where I(0) is the PL intensity just after the pulsed laser excitation; τr is the radiative lifetime of excitons in nc-Si. Wide distribution of the defects f(τ) with recombination lifetimes, τ , leads to the following law of PL relaxation [31] as follows:

<a onClick="popup('http://www.nanoscalereslett.com/content/7/1/446/mathml/M4','MathML',630,470);return false;" target="_blank" href="http://www.nanoscalereslett.com/content/7/1/446/mathml/M4">View MathML</a>

(4)

thumbnailFigure 7. Transients of the PL relaxation. Transients of coated PSiNPs are depicted by red squares and transients of uncoated PSiNPs are depicted by blue triangles (detection wavelength is 600 nm). Lines are results of fitting by Equation 5.

Equation 4 was used to describe the PL transients of self-trapped excitons confined in nc-Si [31] in the following equation:

<a onClick="popup('http://www.nanoscalereslett.com/content/7/1/446/mathml/M5','MathML',630,470);return false;" target="_blank" href="http://www.nanoscalereslett.com/content/7/1/446/mathml/M5">View MathML</a>

(5)

where τ0 is the mean decay time and β is a parameter related to the dispersion of f(τ).

The fitting of the PL transients by Figure 5 gives τ0 = 5.1 μs, β = 0.57 for uncoated PSiNPs (blue line in Figure 7) and τ0 = 16 μs, β = 0.73 for coated PSiNPs (red line in Figure 7). Since the PL lifetime is significantly longer for the coated PSiNPs than for uncoated ones, it evidences the lower defect concentration for nc-Si in coated PSiNPs. The higher value of β for the coated samples points to a smaller energy dispersion of the defect states. Note that the obtained τ0 and β values for the coated PSiNPs are close to the corresponding values for highly luminescent nc-Si in SiO2 matrix formed by high temperature annealing of SiO/SiO2 structures [32]. This fact confirms the suggestion about perfect passivation of the nonradiative defects in the coated PSiNPs.

Conclusions

We have demonstrated the significant enhancement of the photoluminescence efficiency of aqueous suspensions of porous silicon nanoparticles covered by PLGA/PVA. This polymer coating was suggested to prevent silicon nanocrystals in porous silicon from dissolution in water due to the presence of hydrophobic PLGA layer. At the same time, the passivation of the defects on Si nanocrystal surfaces via interaction with water vapors was achieved. The passivation led to the continuous increase of the photoluminescence intensity for 2 weeks. Since the polymer-coated nanoparticles demonstrate high quantum efficiency of photoluminescence (up to 20%) and stable luminescent properties after 1 month storage in water, they are promising for bioimaging applications both in vitro and in vivo. Another advantages of both uncoated and PLGA/PVA-coated porous silicon nanoparticles as labels for bioimaging are their high bioresorbability and biocompatibility.

Competing interests

The authors declare that they have no competing interests.

Authors' contributions

MBG performed fabrication of the PSi samples, measurements of kinetics, data analysis and wrote the text of the article. AYK participated in fabrication of the PSi samples, carried out most part of the experiments, and also wrote some parts of the article. JJ, HL, and BHC contributed in PLGA/PVA coating and other measurement of structural properties. VYT and LAO performed the general data analysis and discussion of the obtained data. All authors read and approved the final manuscript.

Acknowledgments

The work was partially performed at the User Facilities Center of Lomonosov Moscow State University and supported by the Russian Foundation for Basic Research (project numbers 11-02-90506 and 11-02-01342) and the Ministry of Education and Science of the Russian Federation (contract numbers 11.519.11.3017 and 16.513.12.3010).

References

  1. Beveridge TJ: Mechanism of gram variability in select bacteria.

    J Bacteriol 1990, 172:1609-1620. PubMed Abstract | Publisher Full Text | PubMed Central Full Text OpenURL

  2. Poellinger A, Burock S, Grosenick D, Hagen A, Ludemann L, Diekmann F, Engelken F, Macdonald R, Rinneberg H, Schlag PM: Breast cancer: early- and late-fluorescence near-infrared imaging with indocyanine green – a preliminary study.

    Radiology 2011, 258:409-416. PubMed Abstract | Publisher Full Text OpenURL

  3. Stangl S, Gehrmann M, Dressel R, Alves F, Dullin C, Themelis G, Ntziachristos V, Staeblein E, Walch A, Winkelmann I, Multhoff G: In vivo imaging of CT26 mouse tumours by using cmHsp70.1 monoclonal antibody.

    J Cell Mol Med 2011, 15:874-887. PubMed Abstract | Publisher Full Text OpenURL

  4. Lim YT, Noh YW, Han JH, Cai QY, Yoon KH, Chung BH: Biocompatible polymer-nanoparticle-based bimodal imaging contrast agents for the labeling and tracking of dendritic cells.

    Small 2008, 10:1640-1645. OpenURL

  5. Grama CN, Ankola DD, Ravi Kumar MNV: Poly(lactide-co-glycolide) nanoparticles for peroral delivery of bioactives.

    Curr Op Coll & Interface Sci 2011, 16:238-245. Publisher Full Text OpenURL

  6. Canham LT: Bioactive silicon structure fabrication through nanoetching techniques.

    Adv Mater 1995, 7:1033-1037. Publisher Full Text OpenURL

  7. Cullis AG, Canham LT, Calcott PD: The structural and luminescence properties of porous silicon.

    J Appl Phys 1997, 82:909-965. Publisher Full Text OpenURL

  8. Kovalev D, Heckler H, Polisski G, Koch F: Optical properties of Si nanocrystals.

    Phys Status Solidi B 1999, 215:871-932. Publisher Full Text OpenURL

  9. Jurbergs D, Rogojina E, Mangolini L, Kortshagen U: Silicon nanocrystals with ensemble quantum yields exceeding 60%.

    Appl Phys Lett 2006, 88:233116. Publisher Full Text OpenURL

  10. Osminkina LA, Gongalsky MB, Motuzuk AV, Timoshenko VY, Kudryavtsev AA: Silicon nanoparticles as photo- and sono-sensitizers for biomedical application.

    Appl Phys B 2011, 105:665-668. Publisher Full Text OpenURL

  11. Xiao L, Gu L, Howell SB, Sailor MJ: Porous silicon nanoparticle photosensitizers for singlet oxygen and their phototoxicity against cancer cells.

    ACS Nano 2011, 5:3651-3659. PubMed Abstract | Publisher Full Text | PubMed Central Full Text OpenURL

  12. Timoshenko VY, Kudryavtsev AA, Osminkina LA, Vorontsov AS, Ryabchikov YV, Belogorokhov IA, Kovalev D, Kashkarov PK: Silicon nanocrystals as photosensitizers of active oxygen for biomedical applications.

    JETP Lett 2006, 83:423-426. Publisher Full Text OpenURL

  13. Dubertret B, Skourides P, Norris DJ, Noireaux V, Brivanlou AH, Libchaber A: In vivo imaging of quantum dots encapsulated in phospholipid micelles.

    Science 2002, 298:1759-1762. PubMed Abstract | Publisher Full Text OpenURL

  14. Durnev A, Solomina A, Shreder E, Nemova E, Shreder O, Daugel’-Dauge N, Zhanataev A, Veligura V, Osminkina LA, Gongalsky MB, Timoshenko VY: In vivo study of genotoxicity and teratogenicity of silica nanocrystals.

    Int J Biomed Nanosci Nanotech 2010, 1:70-86. Publisher Full Text OpenURL

  15. Canham LT: Nanoscale semiconducting silicon as a nutritional food additive.

    Nanotechnology 2007, 18:185704. Publisher Full Text OpenURL

  16. Erogbogbo F, Yong KT, Roy I, Xu GX, Prasad P, Swihart MT: Biocompatible luminescent silicon quantum dots for imaging of cancer cells.

    ACS Nano 2008, 5:873-878. OpenURL

  17. Park JH, Gu L, von Maltzahn G, Ruoslahti E, Bhatia SN, Sailor MJ: Biodegradable luminescent porous silicon nanoparticles for in vivo applications.

    Nat Mater 2009, 8:331-336. PubMed Abstract | Publisher Full Text | PubMed Central Full Text OpenURL

  18. Erogbogbo F, Yong KT, Roy I, Hu R, Law WC, Zhao W, Ding H, Wu F, Kumar R, Swihart MT, Prasad PN: In vivo targeted cancer imaging, sentinel lymph node mapping and multi-channel imaging with biocompatible silicon nanocrystals.

    ACS Nano 2011, 5:413-423. PubMed Abstract | Publisher Full Text OpenURL

  19. Rosso-Vasic M, Spruijt E, Popovic Z, Overgaag K, van Lagen B, Grandidier B, Vanmaekelbergh D, Domınguez-Gutierrez D, De Cola L, Zuilhof H: Amine-terminated silicon nanoparticles.

    J Mat Chem 2009, 19:5926-5933. Publisher Full Text OpenURL

  20. Kusova K: Silicon nanocrystals as fast and efficient light emitters for optical gain.

    J Non-Crystall Sol 2011. Publisher Full Text OpenURL

  21. Mariotti D, Svrcek V, Hamilton JW, Schmidt M, Kondo M: Silicon nanocrystals in liquid media: optical properties and surface stabilization by microplasma-induced non-equilibrium liquid chemistry.

    Adv Func Mat 2012, 22:954-964. Publisher Full Text OpenURL

  22. Henderson EJ, Shuhendler AJ, Prasad P, Baumann V, Maier-Flaig F, Faulkner DO, Lemmer U, Wu XY, Ozin GA: Colloidally stable silicon nanocrystals with near-infrared photoluminescence for biological fluorescence imaging.

    Small 2011, 17:2507-2516. OpenURL

  23. Osminkina LA, Tamarov KP, Sviridov AP, Galkin RA, Gongalsky MB, Solovyev VV, Kudryavtsev AA, Timoshenko VY: Photoluminescent biocompatible silicon nanoparticles for cancer theranostic applications.

    J Biophot 2012, 5:529-535. Publisher Full Text OpenURL

  24. Mandal TK, Bostanian LA, Graves RA, Chapman SR: Poly(d, l-lactide-co-glycolide) encapsulated poly(vinyl alcohol) hydrogel as a drug delivery system.

    Pharma Res 2002, 19:1713-1719. Publisher Full Text OpenURL

  25. Thiess W: Optical properties of porous silicon.

    Surf Sci Rep 1997, 29:91-192. Publisher Full Text OpenURL

  26. Yadav LDS: Organic spectroscopy. Kluwer, Dordrecht; 2005. OpenURL

  27. Yang TH, Dong A, Meyer J, Johnson OL, Cleland JL, Carpenter JF: Use of infrared spectroscopy to assess secondary structure of human growth hormone within biodegradable microspheres.

    J Pharma Sci 1999, 88:161-165. Publisher Full Text OpenURL

  28. Gongalsky MB, Kharin AY, Zagorodskikh SA, Osminkina LA, Timoshenko VY: Photosensitized generation of singlet oxygen in porous silicon studied by simultaneous measurements of luminescence of nanocrystals and oxygen molecules.

    J Appl Phys 2011, 110:013707. Publisher Full Text OpenURL

  29. Konstantinova EA, Dittrich T, Timoshenko VY, Kashkarov PK: Adsorption-induced modification of spin and recombination centers in porous silicon.

    Thin Solid Films 1996, 276:265-267. Publisher Full Text OpenURL

  30. Delarue C, Allan G, Lannoo M: Theoretical aspects of the luminescence of porous silicon.

    Phys Rev B 1993, 48:11024-11036. Publisher Full Text OpenURL

  31. Kobitski AY, Zhuravlev KS: Self-trapped exciton recombination in silicon nanocrystals.

    Phys Rev B 2001, 63:115423. OpenURL

  32. Timoshenko VY, Lisachenko MG, Shalygina OA, Kamenev BV, Zhigunov DM, Teterukov SA, Kashkarov PK: Comparative study of photoluminescence of undoped and erbium-doped size-controlled nanocrystalline Si/SiO2 multilayered structures.

    J Appl Phys 2004, 96:2254-2260. Publisher Full Text OpenURL