Open Access Highly Accessed Nano Express

p-Cu2O-shell/n-TiO2-nanowire-core heterostucture photodiodes

Tsung-Ying Tsai1, Shoou-Jinn Chang1, Ting-Jen Hsueh2*, Han-Ting Hsueh2, Wen-Yin Weng1, Cheng-Liang Hsu3 and Bau-Tong Dai2

Author affiliations

1 Institute of Microelectronics and Department of Electrical Engineering, Center for Micro/Nano Science and Technology, Advanced Optoelectronic Technology Center, National Cheng Kung University, Tainan, 701, Taiwan

2 National Nano Device Laboratories, Tainan, 741, Taiwan

3 Department of Electronic Engineering, National University of Tainan, Tainan, 700, Taiwan

For all author emails, please log on.

Citation and License

Nanoscale Research Letters 2011, 6:575  doi:10.1186/1556-276X-6-575


The electronic version of this article is the complete one and can be found online at: http://www.nanoscalereslett.com/content/6/1/575


Received:8 September 2011
Accepted:31 October 2011
Published:31 October 2011

© 2011 Tsai et al; licensee Springer.

This is an Open Access article distributed under the terms of the Creative Commons Attribution License (http://creativecommons.org/licenses/by/2.0), which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

Abstract

This study reports the deposition of cuprous oxide [Cu2O] onto titanium dioxide [TiO2] nanowires [NWs] prepared on TiO2/glass templates. The average length and average diameter of these thermally oxidized and evaporated TiO2 NWs are 0.1 to 0.4 μm and 30 to 100 nm, respectively. The deposited Cu2O fills gaps between the TiO2 NWs with good step coverage to form nanoshells surrounding the TiO2 cores. The p-Cu2O/n-TiO2 NW heterostructure exhibits a rectifying behavior with a sharp turn-on at approximately 0.9 V. Furthermore, the fabricated p-Cu2O-shell/n-TiO2-nanowire-core photodiodes exhibit reasonably large photocurrent-to-dark-current contrast ratios and fast responses.

Introduction

UV photodetectors are important devices that have a range of commercial, research, and military applications. They can be used for space communication, ozone layer monitoring, and flame detection [1]. In recent years, high-performance GaN-based (including AlGaN and AlInN) [2-5], ZnO-based [6], and ZnSe-based [7] photodetectors have all been demonstrated. However, high-quality GaN-based UV photodetectors could only be prepared on a sapphire substrate, which is much more expensive as compared with a glass substrate. On the other hand, the photocurrent-to-dark-current contrast ratio of ZnO-based UV photodetectors is still low. Titanium dioxide [TiO2] is a potentially useful wide direct-bandgap material (3.2 eV for anatase and 3.0 eV for rutile) for UV photodetectors, solar cells, and gas sensors due to its outstanding physical, chemical, and optical properties [8-10]. TiO2 is a nontoxic naturally n-type semiconductor material which has a high-temperature stability and low-production costs.

For two-dimensional [2D] films, TiO2 UV photodetectors such as metal-semiconductor-metal detectors and Schottky barrier diodes have been demonstrated [11,12]. It is difficult to produce p- and n-type materials simultaneously, which is necessary for certain device applications. Zhang et al. reported the formation of a 2D TiO2/Cu2O composite film for a photocatalyst application using the metal ion-implantation method [13-15]. Cuprous oxide [Cu2O] is naturally a p-type direct-bandgap semiconductor with a cubic crystal structure and a room-temperature bandgap energy of 2.17 eV [16], which makes it ideal for TiO2-based p-n heterojunctions. Cu2O can be deposited using methods such as thermal oxidation, anodic oxidation, sputtering, solution growth, sol-gel, and electro-deposition [17-24]. Among these methods, sputtering is commonly used in the semiconductor industry. By carefully controlling the growth parameters, high-quality 2D Cu2O films can be produced by direct-current [DC] sputtering [18].

Recently, one-dimensional oxide semiconducting materials have attracted a lot of attention for potential application in optoelectronic devices due to their large surface-area-to-volume ratio [25]. Wu et al. reported the growth of TiO2 nanowires [NWs] on glass substrates by the thermal oxidation-evaporation method [26,27]. They produced single-crystalline TiO2 NWs, whose size and density were controlled by adjusting the growth parameters. However, no report on the fabrication of p-Cu2O-shell/n-TiO2-nanowire-core heterojunction UV photodetectors could be found in the literature, to our knowledge. The present study reports the deposition of p-Cu2O film onto n-TiO2 NWs by DC sputtering and the fabrication of radial p-Cu2O-shell/n-TiO2-nanowire-core photodiodes. The physical, electrical, and optical properties of the fabricated radial p-Cu2O-shell/n-TiO2-nanowire-core photodiodes are discussed.

Experimental section

Before the growth of TiO2 NWs, a Corning 1737 glass substrate (Corning Display Technologies Taiwan Co., Ltd., Taipei City, Taiwan) was wet-cleaned with acetone and deionized water. The glass substrate was subsequently baked at 100°C for 10 min to evacuate moisture. A 400-nm-thick titanium [Ti] film layer was then deposited onto the glass substrate by electron-beam evaporation. Finally, the samples were annealed in a furnace at 700°C for 3 h to synthesize TiO2 NWs in argon [Ar] ambiance. The crystal quality of the as-grown NWs was then characterized by an X-ray diffractometer [XRD] (MXP 18, MAC Science Co., Tokyo, Japan). The surface morphology of the samples and the size distribution of the NWs were characterized by a field-emission scanning electron microscope [FE-SEM] (JEOL JSM-7000F, JEOL Ltd., Tokyo, Japan).

To investigate the deposition of Cu2O, glass was used as the substrate. The target used to deposit Cu2O was a 4-N pure copper block mounted on the cathode. The distance between the target and the sample was fixed at 60 mm. A rotating magnet fixed on the backside of the cathode was used to enhance the plasma bombardment effect. During sputtering, the Ar flow rate, deposition time, base pressure, and chamber pressure were kept at 15 sccm, 10 min, 2 × 10-6 Torr, and 6 mTorr, respectively, and the DC power, O2 flow rate, and substrate temperature were 200 W, 4 sccm, and 25°C, respectively. The crystallography and structure of the deposited Cu2O and the Cu2O/TiO2 NWs were evaluated by XRD and FE-SEM.

Prior to the fabrication of p-Cu2O-shell/n-TiO2-nanowire-core photodiodes, a small piece of glass was used to cover the TiO2 NWs to prevent the deposition of Cu2O in these regions. A 200-nm-thick Cu2O layer was subsequently deposited onto the TiO2 NWs. A 500-nm-thick silver layer was then sputtered onto the Cu2O layer and TiO2 NWs to serve as the p-electrode and n-electrode with a shadow mask. Figure 1 schematically shows the structure of the fabricated p-Cu2O-shell/n-TiO2-nanowire-core photodiodes. A picoammeter (HP-4145B semiconductor parameter analyzer, Agilent Technologies, Sta. Clara, CA, USA), connected via a GPIB controller to a computer, was then used to measure the current-voltage [I-V] characteristics of the fabricated diodes under darkness. The photo responses of the devices were also measured. During photo-response measurements, a 4-W mercury vapor lamp emitting at 365 nm was used as the excitation source.

thumbnailFigure 1. Schematic diagram of fabricated p-Cu2O-shell/n-TiO2-nanowire-core for photodiode measurements.

Results and discussion

Figure 2a shows a cross-sectional FE-SEM image of the TiO2 NWs prepared on a Ti/glass template. It can be clearly seen that high-density TiO2 NWs of various lengths were grown on the Ti/glass template. As shown in Figure 2a, it can be seen that the average length, diameter, and density of these TiO2 NWs were 0.3 μm, 50 nm, and 60 wires/μm2, respectively. Figure 2b shows a cross-sectional FE-SEM image of the sample with Cu2O deposited on TiO2 NWs. As shown, the deposited Cu2O filled the gaps between the TiO2 NWs with good step coverage to form radial Cu2O/TiO2 NWs. It was also found that the deposited Cu2O formed at the sample surface after filling the gaps. In order to investigate the coating performance of Cu2O, the deposited sample was scraped with tweezers into an alcohol solution, which was then ultrasonically treated for 20 min to disperse the NWs. The solution was dropped on carbon tape which was then placed on a hot plate to evacuate the alcohol. Figure 3a shows a SEM image of a single NW. Figures 3b and 3c show energy-dispersive X-ray [EDX] spectroscopic mapping images of Cu and Ti, respectively. These figures correspond to the SEM image shown in Figure 3a. After the deposition of Cu2O, Cu and Ti atoms were distributed over the entire NW. These results suggest that the sputtered Cu2O not only forms the head portion of the nanoclubs, but also forms nanoshells surrounding the TiO2 cores in the nanowire portion of the nanoclubs. The formation of such p-Cu2O-shell/n-TiO2-nanowire-core heterostructure should be able to provide us with a large junction area, which is important for the application of photodetectors.

thumbnailFigure 2. Cross-sectional FE-SEM images. (a) Pure TiO2 nanowires and (b) the sample with Cu2O deposited on TiO2 nanowires at 300°C with 200 W DC power, 6 mTorr chamber pressure, and 3 sccm O2 flow rate.

thumbnailFigure 3. FE-SEM and EDX images. (a) An FE-SEM image of a single radial nanowire. EDX spectroscopic mapping images of (b) Cu and (c) Ti which were corresponded to (a).

Figure 4 shows the crystallographic characteristics obtained from XRD measurements. For the pure TiO2 NWs used for adhesion, the peaks were attributed to the rutile-TiO2 (110) phase (JCPDS Card No. 88-1175). For the p-Cu2O/n-TiO2 NWs, the peaks were attributed to the (110) and (111) phases of the Cu2O phase (JCPDS Card No. 78-2076). No Ti-related signal was found, indicating that the Ti film changed into a TiO2 film after the annealing process.

thumbnailFigure 4. XRD measurements of pure TiO2 nanowires and p-Cu2O/n-TiO2 nanowires obtained by DC sputtering.

Figure 5 shows the dark I-V characteristics measured from the fabricated radial Cu2O/TiO2 NWs. The rectifying behavior indicates that a p-n junction formed in the Cu2O/TiO2 NWs. The operation of the photodiode detector involves three steps (1) the generation of electron-hole [e-h] pairs by the absorption of incident light, whose photon energy exceeds the bandgap of the materials in the device; (2) the separation and transport of the e-h pairs by the internal electric field; and (3) the interaction of current with the external circuit to generate an output signal. Hence, the I-V characteristics of a photodiode in a dark environment are similar to those of a normal rectifying diode. If the p-n junction does not form, the generated e-h pairs will exhibit an ohmic character in the I-V curve and change the resistance. When a photodiode with a p-n junction is illuminated with optical radiation, the I-V characteristics shift according to the photocurrent and reverse current. The measured current in the photodiode, Im, is:

thumbnailFigure 5. Dark I-V characteristic measured from the fabricated radial p-Cu2O/n-TiO2 nanowires.

<a onClick="popup('http://www.nanoscalereslett.com/content/6/1/575/mathml/M1','MathML',630,470);return false;" target="_blank" href="http://www.nanoscalereslett.com/content/6/1/575/mathml/M1">View MathML</a>

where Id is the dark current and Iph is the photocurrent. The presence of a reverse current indicates that the photo response is due to the p-n junction, not the TiO2 NWs or the Cu2O. In the process of measurement under illumination, UV light passes through the TiO2 and illuminates the array of the radial p-Cu2O/n-TiO2 NWs; e-h pairs are produced in the radial NWs when the energy of the UV light is absorbed. The e-h pairs are separated by the internal electric field, and a photocurrent is simultaneously generated. Under forward bias, the turn-on occurred at approximately 0.9 V. With a +5-V applied bias, the forward current of the device was 1.53 × 10-7 A, and with a -5-V applied bias, the reverse leakage current was 7.74 × 10-9 A.

Figure 6 shows the dynamic photo response measured from the fabricated p-Cu2O-shell/n-TiO2-nanowire-core photodiode. With a +10-V applied bias, the dark reverse leakage current of the diode was only around 3.37 × 10-8 A. However, the reverse leakage current increased rapidly to 1.15 × 10-6 A upon UV illumination. When the UV lamp was turned off, the reverse leakage current rapidly decreased to its original value. The reasonably large photocurrent-to-dark-current contrast ratio and the fast responses suggest that the radial p-Cu2O-shell/n-TiO2-nanowire-core photodiodes proposed in this study are potentially useful for UV detector applications.

thumbnailFigure 6. Dynamic photo response measured from the fabricated p-Cu2O-shell/n-TiO2-nanowire-core photodiode.

Conclusions

The deposition of Cu2O onto well-aligned TiO2 NWs by DC sputtering was reported. With the proper sputtering parameters, the deposited Cu2O filled the gaps between the TiO2 NWs with good step coverage to form radial p-Cu2O/n-TiO2 NWs that exhibited rectifying I-V characteristics. The fabricated radial p-Cu2O-shell/n-TiO2-nanowire-core photodiodes had a reasonably large photocurrent-to-dark-current contrast ratio and fast responses.

Competing interests

The authors declare that they have no competing interests.

Authors' contributions

TYT carried out the nanowire experiments and data analysis and wrote the manuscript. SJC and TJH participated in data analysis and revised and finalized the manuscript. HTH designed the thin film and other experiments and data analysis. WYW participated in the revision of the manuscript. CLH provided the concept of the growth process of the nanowire. All the authors contributed to the preparation and revision of the manuscript and approved its final version.

Acknowledgements

The authors would like to thank the National Science Council and Bureau of Energy, Ministry of Economic Affairs of Taiwan, Republic of China for the financial support under contract nos. 100-2221-E-006-040-MY2 and 100-D0204-6 and the LED Lighting Research Center of NCKU for the assistance on device characterization.

References

  1. Monroy E, Calle F, Munoz E, Omnes F, Beaumont B, Gibart P: Visible-blindness in photoconductive and photovoltaic algan ultraviolet detectors.

    J Electron Mater 1999, 28:240-245. Publisher Full Text OpenURL

  2. Chang SJ, Ko TK, Su YK, Chiou YZ, Chang CS, Shei SC, Sheu JK, Lai WC, Lin YC, Chen WS, Shen CF: GaN-based p-i-n sensors with ITO contacts.

    IEEE Sens J 2006, 6:406-411. OpenURL

  3. Zhang J, Zhao H, Tansu N: Large optical gain AlGaN-delta-GaN quantum wells laser active regions in mid- and deep-ultraviolet spectral regimes.

    Appl Phys Lett 2011, 98:171111. Publisher Full Text OpenURL

  4. Zhang J, Tong H, Liu G, Herbsommer JA, Huang G, Tansu N: Characterizations of Seebeck coefficients and thermoelectric figures of merit for AlInN alloys with various In-contents.

    J Appl Phys 2011, 109:053706. Publisher Full Text OpenURL

  5. Zhang J, Kutlu S, Liu G, Tansu N: High-temperature characteristics of Seebeck coefficients for AlInN alloys grown by metalorganic vapor phase epitaxy.

    J Appl Phys 2011, 110:043710. Publisher Full Text OpenURL

  6. Weng WY, Chang SJ, Hsu CL, Hsueh TJ: A ZnO nanowire phototransistor prepared on glass substrates.

    ACS Appl Mat Interfaces 2011, 3:162-166. Publisher Full Text OpenURL

  7. Lin TK, Chang SJ, Su YK, Chiou YZ, Wang CK, Chang CM, Huang BR: ZnSe homoepitaxial MSM photodetectors with transparent ITO contact electrodes.

    IEEE Trans Electron Devices 2005, 52:121-123. Publisher Full Text OpenURL

  8. Chiba Y, Islam A, Komiya R, Koide N, Han L: Conversion efficiency of 10.8% by a dye-sensitized solar cell using a TiO2 electrode with high haze.

    Appl Phys Lett 2006, 88:223505-223507. Publisher Full Text OpenURL

  9. Kopidakis N, Neale NR, Zhu K, Lagemaat JVD, Frank AJ: Spatial location of transport-limiting traps in TiO2 nanoparticle films in dye-sensitized solar cells.

    Appl Phys Lett 2005, 87:202106-202108. Publisher Full Text OpenURL

  10. Shen L, Zhu G, Guo W, Tao C, Zhang X, Liu C, Chen W, Ruan S, Zhong Z: Performance improvement of TiO2/P3HT solar cells using CuPc as a sensitizer.

    Appl Phys Lett 2008, 92:073307-073309. Publisher Full Text OpenURL

  11. Xue H, Kong X, Liu Z, Liu C, Zhou J, Chen W, Ruan S, Xu Q: TiO2 based metal-semiconductor-metal ultraviolet photodetectors.

    Appl Phys Lett 2007, 90:201118-201120. Publisher Full Text OpenURL

  12. Kong X, Liu C, Dong W, Zhang X, Tao C, Shen L, Zhou J, Fei Y, Ruan S: Metal-semiconductor-metal TiO2 ultraviolet detectors with Ni electrodes.

    Appl Phys Lett 2009, 94:123502-123504. Publisher Full Text OpenURL

  13. Zhang KJ, Xu W, Li XJ, Zheng SJ, Xu G, Wang JH: Photocatalytic oxidation activity of titanium dioxide film enhanced by Mn non-uniform doping.

    Trans Nonferrous Met SOC China 2006, 16:1069-1075. Publisher Full Text OpenURL

  14. Yasomanee JP, Bandara J: Multi-electron storage of photoenergy using Cu2O-TiO2 thin film photocatalyst.

    Sol Energy Mat Sol Cells 2008, 92:348-352. Publisher Full Text OpenURL

  15. Zhang YG, Ma LL, Li JL, Yu Y: In situ Fenton reagent generated from TiO2/Cu2O composite film: a new way to utilize TiO2 under visible light irradiation.

    Environ Sci Technol 2007, 41:6264-6269. PubMed Abstract | Publisher Full Text OpenURL

  16. Siripala W, Ivanovskaya A, Jaramillo TF, Baeck SH, McFarland EW: A Cu2O/TiO2 heterojunction thin film cathode for photoelectrocatalysis.

    Sol Energy Mat Sol Cells 2003, 77:229-237. Publisher Full Text OpenURL

  17. Ghijsen J, Tjeng LH, Elp JV, Eskes H, Westerink J, Sawatzky GA, Czyzyk MT: Electronic structure of Cu2O and CuO.

    Phys Rev B 1988, 38:11322-11330. Publisher Full Text OpenURL

  18. Ishizuka S, Kato S, Okamoto Y, Sakurai T, Akimoto K, Fujiwara N, Kobayashi H: Passivation of defects in polycrystalline Cu2O thin films by hydrogen or cyanide treatment.

    Appl Surf Sci 2003, 216:94-97. Publisher Full Text OpenURL

  19. Herion J, Niekisch EA, Scharl G: Investigation of metal oxide/cuprous oxide heterojunction solar cells.

    Sol Energy Mater 1980, 4:101-112. Publisher Full Text OpenURL

  20. Fortin E, Masson D: Photovoltaic effects in Cu2O-Cu solar cells grown by anodic oxidation.

    Solid State Electron 1982, 25:281-283. Publisher Full Text OpenURL

  21. Fernando CAN, Wetthasinghe SK: Investigation of photoelectrochemical characteristics of n-type Cu2O films.

    Sol Energy Mater Sol Cells 2000, 63:299-308. Publisher Full Text OpenURL

  22. Armelao L, Barreca D, Bertapelle M, Bottaro Y, Sada C, Tondello E: A sol-gel approach to nanophasic copper oxide thin films.

    Thin Solid Films 2003, 442:48-52. Publisher Full Text OpenURL

  23. Golden TD, Shumsky MG, Zhou Y, VanderWerf RA, Leeuwen RAV, Switzer JA: Electrochemical deposition of copper (I) oxide films.

    Chem Mater 1996, 8:2499-2504. Publisher Full Text OpenURL

  24. Mahalingam T, Chitra JSP, Chu JP, Sebastian PJ: Preparation and microstructural studies of electrodeposited Cu2O thin films.

    Mater Lett 2004, 58:1802-1807. Publisher Full Text OpenURL

  25. Hsueh TJ, Chen HY, Tsai TY, Weng WY, Yeh YM, Dai BT, Shieh JM: Si nanowire-based photovoltaic devices prepared at various temperatures.

    IEEE Electron Dev Lett 2010, 31:1275-1277. OpenURL

  26. Wu JM, Shih HC, Wu WT: Electron field emission from single crystalline TiO2 nanowires prepared by thermal evaporation.

    Chen Phys Lett 2005, 413:490-494. Publisher Full Text OpenURL

  27. Wu JM, Shih HC, Wu WT: Formation and photoluminescence of single-crystalline rutile TiO2 nanowires synthesized by thermal evaporation.

    Nanotechnology 2006, 17:105-109. Publisher Full Text OpenURL