SpringerOpen Newsletter

Receive periodic news and updates relating to SpringerOpen.

Open Access Nano Express

InGaAs Quantum Well Grown on High-Index Surfaces for Superluminescent Diode Applications

Zhenhua Li1, Jiang Wu2*, Zhiming M Wang1, Dongsheng Fan2, Aqiang Guo1, Shibing Li2, Shui-Qing Yu2, Omar Manasreh12 and Gregory J Salamo12

Author Affiliations

1 Arkansas Institute For Nanoscale Materials Science and Engineering, University of Arkansas, Fayetteville, AR, 72701, USA

2 Department of Electrical Engineering, University of Arkansas, Fayetteville, AR, 72701, USA

For all author emails, please log on.

Nanoscale Research Letters 2010, 5:1079-1084  doi:10.1007/s11671-010-9605-2

The electronic version of this article is the complete one and can be found online at:


Received:12 January 2010
Accepted:6 April 2010
Published:22 April 2010

© 2010 The Author(s)

Abstract

The morphological and optical properties of In0.2Ga0.8As/GaAs quantum wells grown on various substrates are investigated for possible application to superluminescent diodes. The In0.2Ga0.8As/GaAs quantum wells are grown by molecular beam epitaxy on GaAs (100), (210), (311), and (731) substrates. A broad photoluminescence emission peak (~950 nm) with a full width at half maximum (FWHM) of 48 nm is obtained from the sample grown on (210) substrate at room temperature, which is over four times wider than the quantum well simultaneously grown on (100) substrate. On the other hand, a very narrow photoluminescence spectrum is observed from the sample grown on (311) with FWHM = 7.8 nm. The results presented in this article demonstrate the potential of high-index GaAs substrates for superluminescent diode applications.

Keywords:
Photoluminescence; Quantum well; High-index surfaces; Superluminescent diode; Atomic force microscopy

Introduction

Superluminescent diodes (SLDs) have been of great interest due to various applications, such as optical coherence tomography (OCT) and optical sensors [1,2]. Significant research efforts have been focused upon increasing the spectral bandwidth as broadband SLDs are expected to improve depth resolutions for OCT systems [1-4]. A variety of approaches have been used to broaden the spectral bandwidth by engineering the device active regions through including quantum dots [1], multiple quantum wells (MQWs) [2], stacked twin active layers [5], asymmetric dual quantum wells [6], and quantum-well intermixing [7].

Among the many attempts in broadening the spectral width, there have been surprisingly few, if any, efforts made on high-index substrates based SLDs. Due to the difference in growth kinetic, strain, charge or surface polarity, as well as band structures on high-index surfaces [8-12], semiconductor quantum structures on these surfaces have been showing interesting phenomena [13-16]. For example, lateral ordering of QDs and QD clusters have been observed on B-type high-index surfaces and (731) surface, respectively [17,18]. Even though intensive research efforts and significant progresses have been made on the high-index GaAs surfaces, there is a lack of research on high-indexed substrate for superluminescent diodes.

Accordingly, this work focuses on the effects of surface orientation on morphological and optical properties as well as explores the possibility of high-index surfaces for SLD applications. It has been well known that different substrate orientations have different growth reaction kinetics as well as various microscopic patterning of the surface [19]. The latter property, natural roughness, presents on the high-index substrates influence the structure electronic properties and hence providing an additional means of emission spectrum broadening [20]. Therefore, high-index surfaces may help advance the state of the art in SLDs in broadening emission spectrum. In this article, GaAs (100)-, (210)-, (311)-, and (731)-oriented substrates are used in this study.

Experiment

The In0.2Ga0.8As/GaAs quantum well structures under investigation are grown simultaneously on epi-ready GaAs substrates by a solid-source molecular beam epitaxy (MBE) 32P Riber system. In this work, four substrates (100), (210), (311), and (731) are chosen and mounted side by side on a same molybdenum block. An important point to mention here is that the growth conditions are optimized only for (100)-oriented substrate. After oxide desorption at 600°C, a GaAs buffer layer of 500 nm is grown at substrate temperature of 580°C. The GaAs growth rate is one monolayer (ML) per second. Sequentially, 400-nm GaAs was grown at 0.7 ML/s, followed by 50 nm Al0.3Ga0.7As layer. The active region consists of only one In0.2Ga0.8As quantum well of 7 nm grown at 520°C, sandwiched by 50 nm barriers of GaAs. Another 50-nm Al0.3Ga0.7As layer is grown following the growth of the GaAs barrier. In the end, the entire growth is finished by another layer of 50 nm GaAs, and an additional 7-nm In0.2Ga0.8As is deposited on the surface for morphology study. All samples are not doped to eliminate the doping effects on optical properties of different oriented planes. Morphology study is carried out by an atomic force microscopy (AFM). The optical properties of all samples are studied by photoluminescence (PL) technique from 77 to 295 K. The excitation wavelength and power is 532 nm and 50 mW, respectively.

Results and Discussion

Illustrated in Fig. 1 are the AFM images of the as-grown samples on different oriented GaAs surfaces. It is clear that the surface morphology is strongly dependent on the substrate orientation; the surfaces of (100) and (731) are relatively smooth while three-dimensional structures on (210) and (311) surfaces are well observable. The root mean squared (RMS) roughness for (100), (210), (311), and (731) is 0.40, 4.83, 1.14, and 0.50 nm, respectively. It is worth notice that the very RMS and terraced nanostructures with a large size and height distribution are obtained from (210)-oriented sample, as shown in Fig. 2a2c. Although only equivalent thickness of 7 nm In0.2Ga0.8As is deposited, the height of these terraced nanostructures is as high as ~20 nm. In addition, wire-like nanostructures are also observed on GaAs (311) surface, which also exhibit a height distribution within a range of ~5 nm, as shown in Fig. 2d2f. The significant difference in morphology may be explained by the difference in surface energy, surface strain field, and natural microscopic steps [9]. As a result of such natural variation of surface construction using high-index surfaces, the quantum well energy states can be dispersed and will then lead to inhomogeneously broadened gain spectrum.

thumbnailFigure 1. 5 × 5 μm2 AFM images of surface morphology of 7 nm InGaAs layer on (100), (210), (311), and (731) GaAs surfaces

thumbnailFigure 2. a, b, and c are 5 × 5 μm2 AFM images of In0.2Ga0.8As/GaAs (210) surface structures and a line profile. d, e, and f are 5 × 5 μm2 AFM images of In0.2Ga0.8As/GaAs (311) surface structures and a line profile

In order to get an insight into the optical properties of different oriented samples, PL measurements are carried out at different temperatures. Normalized PL spectra at room temperature and 77 K for all four samples are shown in Fig. 3a, 3b. A large difference in spectra width has been observed for different oriented surfaces. The full width at half-maximum (FWHM) and peak shift of all samples are summarized in Table 1. For the QW on (100) substrate, the PL spectra have FWHMs of 11.6 and 5.4 nm at room temperature and at 77 K, respectively. Meanwhile, the PL spectra of QWs on (210), (311), and (731) surfaces demonstrate considerable difference, with FWHM of 48, 7.4, 9.8 nm at 295 K, and 14.5, 2.9, 4.1 nm at 77 K, respectively. At 295 K as well as 77 K, the sample grown on (210) surface shows the broadest PL spectrum, while the sample on (311) has the narrowest spectrum despite of the higher value of RMS than samples on (100)- and (731)-oriented substrate. As shown in Fig. 3a, the PL spectrum at room temperature of the sample on (210) can be fitted with two Gaussian curves, which may be attributed to transitions from excited states or two groups of size distribution. We believe that the peak at shorter wavelength is due to transitions from excited states. This assumption is supported by PL measurement performed at 77 K to as shown in Fig. 3b. The PL shows an asymmetric spectrum with a tail at shorter wavelength. At such low temperature and excitation, the presence of the tail is a strong evidence of size distribution of the terraced structures. In addition to the spectrum linewidth, a blueshift is observed for the (731)- and (311)-oriented samples and a slightly redshift for (210)-oriented sample. Simply, the PL shift may be attributed to surface roughness, which leads to different degree of confinement [21,22]. For example, the surface roughness of (210)-oriented surface is even larger than the QW thickness, which, therefore, is expected to significantly affect the electronic bands. Moreover, the anisotropy of the heavy-hole bands, surface step density structure, etc. in the different GaAs-oriented surfaces may also account for the shift [23].

thumbnailFigure 3. Normalized PL spectra of In0.2Ga0.8As/GaAs/GaAs nanostructures grown on different surfaces at a room temperature and b 77 K

Table 1. FWHM values of In0.2Ga0.8As/GaAs PL spectra on all orientations, and energy shift ∆E (= E(100) − E(xyz)) for high-index surfaces compared to (100)

In order to obtain additional information about optical properties on different surfaces, temperature-dependent PL measurements are performed. The FWHM from 77 K to 295 K for all samples are plotted in Fig. 4a. The temperature-dependent FWHM of (210) surface shows a significant difference from the results of other surfaces. First, the linewidth of (210) surface is much larger than the linewidth of other surfaces. Second, a non-linear FWHM increase profile as a function of temperature has been seen for the (210) surface, while FWHM of all the left three surfaces demonstrates a monotonic broadening because of electron–phonon scattering. The PL spectra of (210)-oriented surface at different temperatures are plotted in Fig. 4b. Before the tail evolves into a second peak (<160 K), the broadening is mainly from the peak at long wavelength. However, due to the appearance of a second peak at short wavelength, the FWHM of (210) shows a very rapid increase from 160 to 240 K. Besides, the broadening of the PL spectra for (210) surface has a steeper slope than other surfaces at both low and high temperatures. This could be explained by the broad size distribution of the nanoterraces on (210) serving as another broadening factor in addition to the intrinsic electron–phonon scattering.

thumbnailFigure 4. a FWHM of the PL spectra of all samples measured from 77 K to 295 K. b Normalized PL spectra of (210)-oriented sample measured with same excitation power from 77 K to 295 K

Finally, temperature-dependent integrated PL intensity for all surfaces is plotted in Fig. 5. For all orientations, the integrated PL intensity presents a similar decrease behavior, and, however, an unusual rapid decrease is observed for non-(100) orientations as temperature approaching 295 K, which may due to the non-optimized growth conditions for non-(100) surfaces. With suppressed non-radioactive recombination at 77 K, high-integrated PL intensity has been observed for all samples, which indicates comparable quantum efficiency for all substrates. Additionally, even better optical properties have been reported for samples on non-(100) surface compared with (100) surface [9,21,22]. The optimization of growth condition of high-index surface is under investigation for better device performance. Nevertheless, our results demonstrate the potential of using high-index GaAs surface for supperluminescent diodes applications.

thumbnailFigure 5. Integrated PL intensity of all samples at temperatures from 77 K to 295 K

Conclusion

In conclusion, the morphology of In0.2Ga0.8As/GaAs grown on GaAs (100), (210), (311), and (731) substrates has been studied by AFM. Three-dimensional nanostructure has been observed for (210)- and (311)-oriented surfaced. Moreover, the optical properties of the samples have been investigated by PL measurement. Spectral broadening has been observed for sample grown on (210) surface. The results presented in this work suggest future potential of high-index surfaces for superluminescent diode applications.

Acknowledgments

This work was supported by the Arkansas Biosciences Institute and the MRSEC Program of NSF Grant No. (DMR-0520550).

Open Access

This article is distributed under the terms of the Creative Commons Attribution Noncommercial License which permits any noncommercial use, distribution, and reproduction in any medium, provided the original author(s) and source are credited.

References

  1. Zhang ZY, Jiang Q, Luxmoore IJ, Hogg RA: A p-type-doped quantum dot superluminescent LED with broadband and flat-topped emission spectra obtained by post-growth intermixing under a GaAs proximity cap.

    Nanotechnology 2009, 20(5):55204.

    COI number [1:STN:280:DC%2BD1MzitlOhtA%3D%3D]; Bibcode number [2009Nanot..20E5204Z]

    Publisher Full Text OpenURL

  2. Wang J, Hamp MJ, Cassidy DT: Design considerations for asymmetric multiple quantum well broad spectral width superluminescent diodes.

    IEEE J. Quantum Electron. 2008, 44:1256-1262.

    COI number [1:CAS:528:DC%2BD1cXhsV2rsLnM]; Bibcode number [2008IJQE...44.1256W]

    Publisher Full Text OpenURL

  3. Xin Y-C, Martinez A, Saiz T, Moscho AJ, Li Y, Nilsen TA, Gray AL, Lester LF: 1.3-μm quantum-dot multisection superluminescent diodes with extremely broad bandwidth.

    IEEE Photon. Technol. Lett. 2007, 19:501-503.

    Bibcode number [2007IPTL...19..501X]

    Publisher Full Text OpenURL

  4. Zhang ZY, Hogg RA, Xu B, Jin P, Wang ZG: Realization of extremely broadband quantum-dot superluminescent light-emitting diodes by rapid thermal-annealing process.

    Opt. Lett. 2008, 33:1210.

    COI number [1:STN:280:DC%2BD1czltFGnsg%3D%3D]; Bibcode number [2008OptL...33.1210Z]

    PubMed Abstract | Publisher Full Text OpenURL

  5. Mikami O, Yasaka H, Noguchi Y: Broader spectral width InGaAsP stacked active layer superluminescent diodes.

    Appl. Phys. Lett. 1990, 56:987-989.

    COI number [1:CAS:528:DyaK3cXhs1yksbY%3D]; Bibcode number [1990ApPhL..56..987M]

    Publisher Full Text OpenURL

  6. Andreeva EV, Volkov NA, Kostin YO, Lapin PI, Marmalyuk AA, Sabitov DR, Yakubovich SD: Broadband near-IR double quantum-well heterostructure superluminescent diodes.

    Quantum Electron. 2008, 38:744-746.

    COI number [1:CAS:528:DC%2BD1cXhsV2jsLzJ]; Bibcode number [2008QuEle..38..744A]

    Publisher Full Text OpenURL

  7. Ong T, Yin M, Yu Z, Chan Y, Lam Y: High performance quantum well intermixed superluminescent diodes.

    Meas. Sci. Technol. 2004, 15:1591-1595.

    COI number [1:CAS:528:DC%2BD2cXmvFals78%3D]; Bibcode number [2004MeScT..15.1591O]

    Publisher Full Text OpenURL

  8. Shu-Shen L, Jian-Bai X: Effective-mass theory for coupled quantum dots grown on (11 N)-oriented substrates.

    Chin. Phys. 2007, 16:1-5.

    Bibcode number [2007ChPhy..16....1L]

    Publisher Full Text OpenURL

  9. Liang BL, Wang ZM, Sablon KA, Mazur YI, Salamo GJ: Influence of GaAs substrate orientation on InAs quantum dots: surface morphology, critical thickness, and optical properties.

    Nanoscale Res. Lett. 2007, 2:609-613.

    COI number [1:CAS:528:DC%2BD1cXlslejsL4%3D]; Bibcode number [2007NRL.....2..609L]

    Publisher Full Text OpenURL

  10. Wang L, Li M, Xiong M, Zhao L: Effect of interfacial bonds on the morphology of InAs QDs grown on GaAs (311) B and (100) substrates.

    Nanoscale Res. Lett. 2009, 4(7):689-693.

    COI number [1:CAS:528:DC%2BD1MXnt1Skt7g%3D]; Bibcode number [2009NRL.....4..689W]

    PubMed Abstract | Publisher Full Text | PubMed Central Full Text OpenURL

  11. Henini M: Properties and applications of quantum dot heterostructures grown by molecular beam epitaxy.

    Nanoscale Res. Lett. 2006, 1:32-45.

    Bibcode number [2006NRL.....1...32H]

    Publisher Full Text OpenURL

  12. Henini M: High index surfaces grow novel devices.

    III-Vs Rev. 1998, 11:48-52. Publisher Full Text OpenURL

  13. Yazdanpanah VR, Wang ZM, Salamo GJ: Highly anisotropic morphologies of GaAs(331) surfaces.

    Appl. Phys. Lett. 2003, 82:1766.

    COI number [1:CAS:528:DC%2BD3sXhvV2ksrg%3D]; Bibcode number [2003ApPhL..82.1766Y]

    Publisher Full Text OpenURL

  14. Sanguinetti S, Gurioli M, Henini M: Built-in electric fields in InAs quantum dots grown on (N11) GaAs substrates.

    Microelectron. J. 2002, 33:583-588.

    COI number [1:CAS:528:DC%2BD38XksFKnsbk%3D]

    Publisher Full Text OpenURL

  15. Wen H, Wang ZM, Salamo GJ: Atom-resolved scanning tunneling microscopy of (In,Ga)As quantum wires on GaAs(311)A.

    Appl. Phys. Lett. 2004, 84:1756.

    COI number [1:CAS:528:DC%2BD2cXhvFCjt7s%3D]; Bibcode number [2004ApPhL..84.1756W]

    Publisher Full Text OpenURL

  16. Niki N, Morita K, Kitada T, Isu T: Optical anisotropy of strained quantum wells on high index substrates.

    Phys. Status Solid. (c) 2008, 5:2756-2759.

    COI number [1:CAS:528:DC%2BD1cXpsVyitbk%3D]; Bibcode number [2008PSSCR...5.2756N]

    Publisher Full Text OpenURL

  17. Wang ZM, Seydmohamadi S, Lee JH, Salamo GJ: Surface ordering of (In,Ga)As quantum dots controlled by GaAs substrate indexes.

    Appl. Phys. Lett. 2004, 85:5031.

    COI number [1:CAS:528:DC%2BD2cXhtValtbjJ]; Bibcode number [2004ApPhL..85.5031W]

    Publisher Full Text OpenURL

  18. Xie YZ, Kunets VP, Wang ZM, Dorogan VG, Mazur YI, Wu J, Salamo GJ: Multiple stacking of InGaAs/GaAs (731).

    Nano Micro Lett. 2009, 1:1-3.

    COI number [1:CAS:528:DC%2BC3cXjvFemtrk%3D]

    OpenURL

  19. Polimeni A, Patanè A, Henini M, Eaves L, Main PC, Sanguinetti S, Guzzi M: Influence of high-index GaAs substrates on the growth of highly strained (InGa)As/GaAs heterostructures.

    J. Cryst. Growth 1999, 201–202:276-279. Publisher Full Text OpenURL

  20. Henini M, Sanguinetti S, Brusaferri L, Grilli E, Guzzi M, Upward MD, Moriarty P, Beton PH: Structural and optical characterization of self-assembled InAs-GaAs quantum dots grown on high index surfaces.

    Microelectron. J. 1997, 28:933-938. Publisher Full Text OpenURL

  21. González-Borrero PP, Lubyshev DI, Petitprez E, La Scala N, Marega E, Basmaji P: Optical properties of natural InxGa1-xAs quantum dots grown on high-index GaAs substrates.

    Braz. J. Phys. 1997, 27:65-75. OpenURL

  22. Nötzel R, Eissler D, Hohenstein M, Ploog K: Periodic mesoscopic step arrays by step bunching on high-index GaAs surfaces.

    J. Appl. Phys. 1993, 74:431.

    Bibcode number [1993JAP....74..431N]

    Publisher Full Text OpenURL

  23. Li S, Xia J: Effective-mass theory for GaAs/Ga1-xAlxAs quantum wires and corrugated superlattices grown on (311)-oriented substrates.

    Phys. Rev. B 1994, 50:8602-8608.

    COI number [1:CAS:528:DyaK2cXmtlylt7k%3D]; Bibcode number [1994PhRvB..50.8602L]

    Publisher Full Text OpenURL