SpringerOpen Newsletter

Receive periodic news and updates relating to SpringerOpen.

Open Access Nano Express

Self-Assembled 3D Flower-Like Hierarchical β-Ni(OH)2Hollow Architectures and their In Situ Thermal Conversion to NiO

Lu-Ping Zhu12*, Gui-Hong Liao2, Yang Yang2, Hong-Mei Xiao2, Ji-Fen Wang1 and Shao-Yun Fu2

Author Affiliations

1 School of Urban Development and Environmental Engineering, Shanghai Second Polytechnic University, Shanghai, 201209, China

2 Technical Institute of Physics and Chemistry, Chinese Academy of Sciences, Beijing, 100190, China

For all author emails, please log on.

Nanoscale Research Letters 2009, 4:550-557  doi:10.1007/s11671-009-9279-9

The electronic version of this article is the complete one and can be found online at:


Received:16 January 2009
Accepted:11 February 2009
Published:27 February 2009

© 2009 to the authors

Abstract

Three-dimensional (3D) flower-like hierarchicalβ-Ni(OH)2hollow architectures were synthesized by a facile hydrothermal route. The as-obtained products were well characterized by XRD, SEM, TEM (HRTEM), SAED, and DSC-TGA. It was shown that the 3D flower-like hierarchicalβ-Ni(OH)2hollow architectures with a diameter of several micrometers are assembled from nanosheets with a thickness of 10–20 nm and a width of 0.5–2.5 μm. A rational mechanism of formation was proposed on the basis of a range of contrasting experiments. 3D flower-like hierarchical NiO hollow architectures with porous structure were obtained after thermal decomposition at appropriate temperatures. UV–Vis spectra reveal that the band gap of the as-synthesized NiO samples was about 3.57 eV, exhibiting obviously red shift compared with the bulk counterpart.

Keywords:
Ni(OH)2; NiO; Hollow architecture; Hydrothermal synthesis

Introduction

Ordered self-assembly of nanoscale building blocks, such as nanoparticles, nanorods, nanoribbons, and so forth, into complex architectures has recently become a hot topic in material research fields. Remarkable progress has been made in the self-assembly of highly organized building blocks of metals [1-4], semiconductors [5-8], copolymers [9], and organic–inorganic hybrid materials [10] based on different driving mechanisms, such as Ostwald ripening [11], Kirkendall effect [12], and self-assembly of nanoscale blocks through hydrophobic interactions [13]. However, controlled organization into curved hollow structures from the primary building units, for example sheets, remains a challenge for materials self-assembly [14]. The ability to assemble primary units into hollow structures is in great demand not only because of their role in better understanding the concept of self-assembly with artificial building blocks but also due to its great potential for technological applications [15].

Nickel hydroxide (Ni(OH)2), as one of the most important transition metal hydroxides, has received increasing attention due to its extensive applications, especially as a positive electrode active material, in alkaline rechargeable Ni-based batteries [16]. It has been reported that the capacity of the positive electrode could be significantly increased when nanophase Ni(OH)2 was added to micrometer-size spherical Ni(OH)2[17,18]. Further efforts have focused on searching for new synthetic methods of Ni(OH)2 nanocrystals with high quality and various exciting morphologies. 1D, 2D, and 3D nanostructures of Ni(OH)2, including nanorods [19], nanoribbons [20], nanotubes [21], nanosheets [22], and superstructures patterns [23-28], have been fabricated successfully by a variety of methods. Nickel oxide (NiO) is a very prosperous inorganic material which was widely applied in the fields of smart window, electrochemical supercapacitor, battery cathodes, catalyst, etc. [29-32]. NiO can be conveniently prepared by thermal decomposition of its precursors [33]. By contrast, there are only limited reports concerning the synthesis of Ni(OH)2 and NiO hollow architectures and their interesting properties. For example, Wang’s group synthesized hollow architectures of Ni(OH)2 with unusual form and hierarchical structures by using styrene-acrylic acid copolymer (PSA) latex particles as the templates [23]. Hierarchically porous β-Ni(OH)2 microspheres constructed with nanoflakes were recently prepared with the help of hexamethylenetetramine (HMTA) as the basic source, exhibiting small blue shift compared with the bulk counterpart [24]. Duan et al. reported the fabrication of hierarchical Ni(OH)2 monolayer hollow-sphere arrays with a fine structure of nanoflakelets by an electrochemical strategy based on a polystyrene (PS) sphere colloidal monolayer. Such hierarchically structured hollow-sphere arrays have demonstrated a tunable optical transmission stop band in the visible-near-IR (Vis–NIR) region from 455 to 1855 nm, depending on the hollow-sphere size and the fine structure [25]. However, hollow structures prepared from hard templating routes (e.g. PS latex particles) usually suffer from disadvantages related to high cost and tedious synthetic procedures, which may prevent them from being used in large-scale applications [11]. Thus, it still remains a challenge to develop simple approaches to synthesize hierarchical Ni(OH)2 and NiO hollow architectures.

Herein we describe a facile hydrothermal route to synthesize highly ordered 3D flower-like hierarchicalβ-Ni(OH)2hollow architectures with a high yield. The formation mechanism of the 3D flower-like hierarchicalβ-Ni(OH)2hollow architectures was proposed. The morphology-retained NiO hollow architectures with porous structure were readily obtained by thermal decomposition of the as-obtainedβ-Ni(OH)2products. Finally, the optical property of NiO sample was investigated with the help of UV–Vis spectrum.

Experimental Section

Synthesis of 3D Flower-Like Hierarchicalβ-Ni(OH)2and NiO Hollow Architectures

In a typical synthesis, 1 mmol of NiCl2·6H2O was dissolved in 5 mL of deionized (DI) water, followed by an addition of 15 mL of ethanol and 5 mL of CO(NH2)2solution (2 mol L−1) under vigorous stirring. Then, 2 mL of NH3·H2O (35% by v/v) was added dropwise into the above solution to form a clear blue solution. The final solution was transferred to a 50 mL Teflon-lined autoclave. The autoclave was sealed and heated in an oven at 120 °C for 12 h and then allowed to cool to room temperature. The resulting pale green slurry was rinsed with DI water several times to remove soluble impurities. The product was dried in an oven at 50 °C for 8 h to get the sample ofβ-Ni(OH)2. To obtain NiO the as-prepared sample ofβ-Ni(OH)2was calcined in air for 4 h.

Characterization

The phase purity of the products was examined by X-ray powder diffraction (XRD) using a Rigaku D/max 2500 diffractometer at a voltage of 40 kV and a current of 200 mA with Cu-Kα radiation (λ = 1.5406 Å), employing a scanning rate 0.02°/s in the 2θranging from 30 to 80°. Scanning electron microscopy (SEM) images and energy dispersive X-ray (EDX) analysis were obtained using a HITACHI S-4300 microscope (Japan). Transmission electron microscope (TEM) images and the corresponding selected area electron diffraction (SAED) pattern were taken on a Hitachi-600 transmission electron microscope at an accelerating voltage of 200 kV. High-resolution transmission electron microscope (HRTEM) images were carried out for the as-prepared sample using JEOL JEM-2010 transmission electron microscope at an accelerating voltage of 200 kV. The size distribution of the sample was measured using a scale on the magnified SEM micrographs. Thermogravimetric (TGA) and differential scanning calorimetric (DSC) analyses were carried out on a NETZSCH STA-409 PC thermal analyzer with a heating rate of 10 °C min−1in flowing oxygen atmosphere. Room-temperature UV–Vis absorption spectrum was recorded on a Shimadzu UV-1601 PC UV–Vis recording spectrophotometer.

Results and Discussion

The phase structure and purity of the as-synthesized samples were examined by powder XRD. Figure 1shows the XRD pattern of the samples. It can be seen from Fig. 1that all of the diffraction peaks can be indexed to a pure hexagonal structure ofβ-Ni(OH)2(JCPDS No: 14-0117). No diffraction peaks from impurities are found in the samples.

thumbnailFigure 1. XRD pattern of the as-obtainedβ-Ni(OH)2sample

The morphologies of as-synthesized products were examined by SEM and TEM. Figure 2 shows the SEM images of the β-Ni(OH)2 products. Clearly, the products consist of a high yield of fairly uniform particles with the average size of about 4.5 μm in diameter (Fig. 2a), showing a relatively narrow size distribution (inset of Fig. 2a). The detailed morphologies of the as-synthesized products are shown in Fig. 2b and c, which reveal that all the β-Ni(OH)2 particles have 3D flower-like hierarchical morphology. Those 3D flower-like architectures are built from several dozen of nanosheets with a thickness of 10–20 nm and a width of 0.5–2.5 μm. The surface of the sheets assembled into the hierarchical micro-architectures was very smooth, probably due to Ostwald ripening [11]. Furthermore, the broken sphere shown in Fig. 2d indicates that the architectures have a hollow structure.

thumbnailFigure 2. adSEM images with different magnifications of the as-obtainedβ-Ni(OH)2samples. Inset ofa: the size distribution of the as-synthesized sample;eTEM image of one typical hierarchical hollow architectures;fHRTEM image taken from the age of the hexagonal phaseβ-Ni(OH)2sheets and the corresponding selected-area electron diffraction (SAED) pattern (lower left corner)

The morphologies and structures of as-synthesized samples were further characterized by TEM. As shown in Fig. 2e, TEM observations demonstrate that the products are flower-like structures similar to the SEM observation. The remarkable feature of the hollow architectures is the obvious contrast between the dark edge and the pale center, as reported for other hollow particles with a central cavity. To further obtain structural information for the well-aligned sheets, high-resolution TEM (HRTEM) images and the corresponding selected area electron diffraction (SAED) patterns were also recorded on single sheet. In a HRTEM image (Fig. 2f) taken from the edge of a sheet, the lattice fringes are clearly visible with a spacing of 0.27 nm, which is in good agreement with the spacing of the (01-10) planes ofβ-Ni(OH)2(JCPDS No: 14-0117). The corresponding SAED pattern is shown in the inset of Fig. 2f. The SAED and HRTEM analyses reveal that the building units are single-crystal.

In order to reveal the formation process of the 3D flower-like hollow architectures in more detail, time-dependent experiments were carried out and the resultant products were analyzed by TEM. The representative TEM images of the products prepared at certain reaction time intervals are shown in Fig. 3. Under the present synthetic conditions, nanoparticles and some ultra-thin nanosheets can be obtained as a result of aggregation and growth after treatment for 2 h (Fig. 3a). When the reaction time was prolonged to 6 h, besides flower-like hollow architectures, some underdeveloped flower-like hollow architectures also existed in the as-synthesized samples, as shown in Fig. 3b, indicating that oriented attachment is still underway. After the reaction was further prolonged to 12 h, fully developed 3D flower-like hierarchical hollow architectures similar to that shown in Fig. 2are observed (Fig. 3c).

thumbnailFigure 3. TEM images of the as-synthesized samples with treatment times ofa2 h,b6 h, andc12 h at 120 °C. SEM images of the as-synthesized sample obtained at 120 °C for 12 h:dwithout urea;eandfwithout ammonia;gschematic illustration of the formation ofβ-Ni(OH)23D flower-like hollow architectures

In addition, the roles of urea and ammonia were found to be very important for the formation feature of 3D flower-like hollow architectures. In a control experiment, when no urea was added under the same reaction conditions, the products take on a flake-like shape (Fig. 3d) rather than 3D flower-like hierarchical hollow architectures, while the ammonia was absent, only honeycomb-structured micro-architectures can be obtained, as shown in Fig. 3e and f.

On the basis of the above results in the present study, we believe that urea, ammonia, and reaction time play important roles in the formation of 3D flower-like hollow architectures. The formation of 3D flower-like hierarchical hollow architectures may result from the combined roles of urea, ammonia under the appropriate reaction condition. The chemical reaction in the process to obtain Ni(OH)2 3D flower-like hollow microarchitectures could be formulated as follows:

(1)

(2)

(3)

(4)

Most probably, the bubbles of CO2 gas produced in the reaction with the participation of CO(NH2)2 must have played a key role, since no other templates/surfactants/emulsions were used in this work. A possible formation process involving the assembly-then-assemble mechanism can be schematically illustrated in Fig. 3g. In the beginning, Ni2+ in solution reacts first with NH3 to form a relatively stable complex, [Ni(NH3)62+, because of its strong affinity to Ni2+ at room temperature. Afterwards, the complex was decomposed and released NH3 to provide OH ions for the formation of Ni(OH)2 by a hydrothermal treatment. At the same time, with the participation of CO(NH2)2, many micrometer/sub-micrometer CO2 bubbles are produced in the system at 120 °C (step a). The freshly crystalline nanoparticles are unstable because of their high surface energy and tend to aggregate and form higher nanoparticles, driven by the minimization of interfacial energy. In our synthesis, the formation of [Ni(NH3)62+ complex would sharply decreased the free Ni2+ concentration in the solution, which resulted in a relatively low reaction rate of Ni2+ ions with OH ions. A slow reaction rate caused the separation of nucleation and growth steps, which is crucial for high-quality crystal synthesis. As a result, the sheet-like high crystalline Ni(OH)2 was firstly formed (step b), which may be related to the nature of the initial crystal structures [34]. Then the self-assembly and Ostwald ripening process occurs around the gas/liquid interface of CO2 and water, and finally 3D flower-like hierarchical hollow architectures (step c). Here, CO2 bubbles decomposed from CO(NH2)2 can act as soft templates to induce the self-assembly of nanosheets on their surfaces. A similar gaseous bubble has also been used as a template for TiO2 and VOOH hollow nanostructures [35,36], which is different from the assembly-then-inside-out evacuation mechanism in the formation of Fe3O4 hollow spheres [37]. Our time-dependent experiments support the above aggregation-then-assembly mechanism; it is found that the assembly process occurs after the formation of the nanosheets.

The thermal behavior of flower-like hierarchicalβ-Ni(OH)2hollow architectures was investigated with TG and DSC measurements (Fig. 4). A TG curve showed thatβ-Ni(OH)2started to decompose (weight loss) at about 285 °C. The total weight loss was measured to be ~22% which is larger than the theoretical value (19.4%) calculated from the following reaction:

(5)

The powders exhibit thermogravimetric transitions that are likely due to the loss of physical absorbed and structural water. The initial weight loss from 30 to 140 °C is attributed to the loss of surface adsorbed water and ethanol. The weight loss in the range of 140–365 °C is due to the removal of the crystalline water molecules. After 365 °C, the weight loss continued but gradually slowed at 400 °C and almost ceased at 500 °C. As a consequence, the stable residue can reasonably be ascribed to NiO. The DSC curve showed an endothermic peak with a maximum located at 315 °C. The temperature range of the endothermic peak in the DSC curve fits well with that of weight loss in the TG curve, corresponding to endothermic behavior during the decomposition ofβ-Ni(OH)2to NiO.

thumbnailFigure 4. Differential scanning calorimetric analysis (DSC) and thermogravimetric analysis (TG) curves ofβ-Ni(OH)23D flower-like hollow architectures

The nickel hydroxyl can easily be transformed to NiO upon heat treatment. Figure 5shows the XRD patterns of the flower-like hierarchicalβ-Ni(OH)2hollow architectures heated at various temperatures. All the diffraction peaks can be indexed to the face-centered cubic (fcc) NiO phase (JCPDS No. 04-0835). No peaks due toβ-Ni(OH)2are observed, suggesting thatβ-Ni (OH)2is completely converted to NiO after being heated for 4 h, which is also confirmed by TG and DSC studies. Notably, when increasing calcination temperature to 500 °C, all the peaks belonging to NiO cubic phase were markedly sharpening with high intensities, which suggested that the crystallinity of NiO phase was higher at high calcination temperature than that obtained at low calcination temperature.

thumbnailFigure 5. XRD patterns of the as-obtainedβ-Ni(OH)2samples calcined at different temperatures for 4 h: (a) 300 °C and (b) 500 °C

The corresponding SEM images and EDS patterns are presented in Fig. 6. It can be observed from Fig. 6a, after annealing for 4 h in air, the morphology and structure of the flower-like hierarchical hollow architectures were sustained very well, which may due to the in situ conversion of β-Ni(OH)2 nanosheets to NiO nanosheets [23]. In addition, the nanocontact between particles may also stabilize the 3D flower-like structure mechanically against collapse or fracture [27]. The magnified SEM image shown in Fig. 6b and c displays that pores were produced among the nanosheets. This kind of porous structure was formed due to the dehydration and decomposition of Ni(OH)2 during heating. The EDS result shown in Fig. 6d demonstrates that the as-prepared sample contains Ni and O, and the atomic ratio of Ni and O is ~44.01:40.14, which agrees well with the stoichiometry of NiO. The Au peaks come from the thin gold layer for conductive coating (the signal of C is from the conductive adhesive). Shown in the inset of Fig. 6d is the SAED pattern that was recorded from the individual nanosheet, which can be indexed to the face-centered cubic structure with phase purity. It is interesting and surprising that the porous nanosheet still exhibits an almost single-crystalline diffraction pattern. Here, heat treatment may provide the energy to make the NiO particles self-assembled with high orientation and kept the former single-crystalline nature of the sheets [38].

thumbnailFigure 6. aSEM image of double typical 3D flower-like hierarchical NiO architectures;bcthe corresponding enlarged SEM images of the area marked with a red rectangle. Insetcis a high-magnification TEM image of a sheet;dEDS result of the as-obtainedβ-Ni(OH)2samples calcined at 500 °C for 4 h. Inset ofdshows SAED pattern of the NiO nanosheet

The UV–Vis absorption spectrum of the sample is presented in Fig. 7. The strong absorption in the UV region can be observed, which is attributed to the band gap absorption of the as-synthesized NiO sample. In principle, the optical band gap energy Eg for a semiconductor can be estimated by the equation [39]:

(6)

where α is the absorption coefficient, is the photon energy, B is a constant relative to the materials n is either 2 for direct inter-band transition or 1/2 for indirect inter-band transition [27]. The inset of Fig. 7 shows the (αhν)2 curve for the sample. The band gap of the as-synthesized NiO samples was about 3.57 eV by the extrapolation of the above equation, which shows obvious red-shift compared with that of the bulk NiO (4.0 eV) [40]. Such a difference could be contributed to their spherical hollow hierarchical architectures and the small thickness of the sheets with porous structures, in which the interactions between the connected building blocks led to a quantum size effect [41]. No linear relation was found for n = 1/2, indicating that the as-prepared NiO samples have a direct band gap.

thumbnailFigure 7. UV–Vis absorption spectrum for the as-synthesized NiO samples. The inset is the (αhν)2curve

Conclusions

The 3D flower-like hierarchicalβ-Ni(OH)2hollow architectures have been synthesized by a facile hydrothermal route in the presence of urea and ammonia. The 3D flower-like hollow architectures with the size of several micrometers are composed of nanosheets of 10–20 nm in thickness. The results indicated that the reaction time, urea and ammonia play important roles in the formation of 3D flower-like hierarchicalβ-Ni(OH)2hollow architectures. By calcining the as-prepared flower-likeβ-Ni(OH)2hollow architectures, hierarchical NiO crystallites with porous single-crystalline nanosheets were obtained, well inheriting the shapes of theβ-Ni(OH)2samples. The optical absorption band gap of the as-obtained NiO samples is determined to be 3.57 eV. Due to the unique architectures, the as-obtained products may have potential applications in water treatment, electrode, sensors, catalysts, biomarkers, microelectronics, energy storage, and other related micro/nanoscale devices due to their unique architectures.

Acknowledgments

This work was financially supported by the National Natural Science Foundation of China (Nos.: 50573090 and 10672161) and Beijing Municipal Natural Science Foundation (No. 2082023).

References

  1. Kaltenpoth G, Himmelhaus M, Slansky L, Caruso F, Grunze M:

    Adv Mater. 2003, 15:1113.

    COI number [1:CAS:528:DC%2BD3sXls1Kks7c%3D]

    Publisher Full Text OpenURL

  2. Hou Y, Kondoh H, Ohta T:

    Chem Mater. 2005, 17:3994.

    COI number [1:CAS:528:DC%2BD2MXlsVeltro%3D]

    Publisher Full Text OpenURL

  3. Zhu LP, Xiao HM, Zhang WD, Yang Y, Fu SY:

    Cryst Growth Des. 2008, 8:1113.

    COI number [1:CAS:528:DC%2BD1cXivVSksLg%3D]

    Publisher Full Text OpenURL

  4. Zhu LP, Zhang WD, Xiao HM, Yang Y, Fu SY:

    J. Phys. Chem. C. 2008, 112:10073.

    COI number [1:CAS:528:DC%2BD1cXnt1Cltbc%3D]

    Publisher Full Text OpenURL

  5. Yuan J, Laubernds K, Zhang Q, Suib SL:

    J Am Chem Soc. 2003, 125:4966.

    COI number [1:CAS:528:DC%2BD3sXis1eqtLk%3D]

    Publisher Full Text OpenURL

  6. Yada M, Taniguchi C, Torikai T, Watari T, Furuta S, Katsuki H:

    Adv Mater. 2004, 16:1448.

    COI number [1:CAS:528:DC%2BD2cXnvFyisLs%3D]

    Publisher Full Text OpenURL

  7. Hu J, Ren L, Guo Y, Liang H, Cao A, Wan L, Bai C:

    Angew Chem Int Ed. 2005, 44:1269.

    COI number [1:CAS:528:DC%2BD2MXhs1yrurc%3D]

    Publisher Full Text OpenURL

  8. Zhu LP, Xiao HM, Liu XM, Fu SY:

    J Mater Chem. 2006, 16:1794.

    COI number [1:CAS:528:DC%2BD28XktlSiurg%3D]

    Publisher Full Text OpenURL

  9. Jenekhe SA, Chen XL:

    Science. 1998, 279:1903.

    COI number [1:CAS:528:DyaK1cXhvFKnsbg%3D]; Bibcode number [1998Sci...279.1903J]

    Publisher Full Text OpenURL

  10. Du J, Chen Y:

    Angew Chem Int Ed. 2004, 43:5084.

    COI number [1:CAS:528:DC%2BD2cXotlKrtLY%3D]

    Publisher Full Text OpenURL

  11. Lou XW, Yuan C, Rhoades E, Zhang Q, Archer LA:

    Adv. Funct. Mater. 2006, 16:1679.

    COI number [1:CAS:528:DC%2BD28XhtVSktL7I]

    Publisher Full Text OpenURL

  12. Yin Y, Rioux RM, Erdonmez CK, Hughes S, Somorjai GA, Alivisatos AP:

    Science. 2004, 304:711.

    COI number [1:CAS:528:DC%2BD2cXjsV2gt7g%3D]; Bibcode number [2004Sci...304..711Y]

    Publisher Full Text OpenURL

  13. Park S, Lim JH, Chung SW, Mirkin CA:

    Science. 2004, 303:348.

    COI number [1:CAS:528:DC%2BD2cXjtFGntw%3D%3D]; Bibcode number [2004Sci...303..348P]

    Publisher Full Text OpenURL

  14. Liu B, Zeng HC:

    J Am Chem Soc. 2004, 126:8124.

    COI number [1:CAS:528:DC%2BD2cXks1GisLk%3D]

    Publisher Full Text OpenURL

  15. Noble PF, Cayre OJ, Alargova RG, Velev OD, Paunov VN:

    J Am Chem Soc. 2004, 126:8092.

    COI number [1:CAS:528:DC%2BD2cXks1GisLg%3D]

    Publisher Full Text OpenURL

  16. French HM, Henerson MJ, Hillman AR, Vieil E:

    J Electroanal Chem. 2001, 500:192.

    COI number [1:CAS:528:DC%2BD3MXhslelsL4%3D]

    Publisher Full Text OpenURL

  17. Liu XH, Yu L:

    J Power Sources. 2004, 128:326.

    COI number [1:CAS:528:DC%2BD2cXhvVGrurY%3D]

    Publisher Full Text OpenURL

  18. Han XJ, Xie XM, Xu CQ, Zhou DR, Ma YL:

    Opt Mater. 2003, 23:465.

    COI number [1:CAS:528:DC%2BD3sXksVehsb4%3D]; Bibcode number [2003OptMa..23..465H]

    Publisher Full Text OpenURL

  19. Liang JH, Li YD:

    Chem Lett. 2003, 32:1126.

    COI number [1:CAS:528:DC%2BD3sXpslGltb4%3D]

    Publisher Full Text OpenURL

  20. Yang DN, Wang RM, Zhang J, Liu ZF:

    J Phys Chem B. 2004, 108:7531.

    COI number [1:CAS:528:DC%2BD2cXktVamtrg%3D]

    Publisher Full Text OpenURL

  21. Tao F, Guan M, Zhou Y, Zhang L, Xu Z, Chen J:

    Cryst Growth Des. 2008, 8:2157.

    COI number [1:CAS:528:DC%2BD1cXmvVGqurY%3D]

    Publisher Full Text OpenURL

  22. Ni X, Zhao Q, Li B, Cheng J, Zheng H:

    Solid State Commun. 2006, 137:585.

    COI number [1:CAS:528:DC%2BD28XitVehs7o%3D]; Bibcode number [2006SSCom.137..585N]

    Publisher Full Text OpenURL

  23. Wang D, Song C, Hu Z, Fu X:

    J Phys Chem B. 2005, 109:1125. Publisher Full Text OpenURL

  24. Duan G, Cai W, Luo Y, Sun F:

    Adv. Funct. Mater.. 2007, 17:644.

    COI number [1:CAS:528:DC%2BD2sXjs1WqtL8%3D]

    Publisher Full Text OpenURL

  25. Yang L, Zhu Y, Tong H, Liang Z, Wang W:

    Cryst Growth Des. 2007, 7:2716.

    COI number [1:CAS:528:DC%2BD2sXhtFyiurrE]

    Publisher Full Text OpenURL

  26. Luo Y, Duan G, Li G:

    J Solid State Chem. 2007, 180:2149.

    COI number [1:CAS:528:DC%2BD2sXnvFyltb0%3D]; Bibcode number [2007JSSCh.180.2149L]

    Publisher Full Text OpenURL

  27. Xu L, Ding Y-S, Chen C-H, Zhao L, Rimkus C, Joesten R, Suib SL:

    Chem Mater. 2008, 20:308.

    COI number [1:CAS:528:DC%2BD2sXhsVWqs7vN]

    Publisher Full Text OpenURL

  28. He J, Lindstrom M, Hagfeldt A, Lindquist SE:

    J Phys Chem B. 1999, 103:8940.

    COI number [1:CAS:528:DyaK1MXmt12muro%3D]

    Publisher Full Text OpenURL

  29. Stadniychuk HP, Anderson MA, Chapman TW:

    J. Electrochem. Soc.. 1996, 143:1629.

    COI number [1:CAS:528:DyaK28XjtFSjtL8%3D]

    Publisher Full Text OpenURL

  30. Yoshio M, Todorov Y, Yamato K, Noguchi H, Itoh J, Okada M, Mouri T:

    J Power Sources. 1998, 74:46.

    COI number [1:CAS:528:DyaK1cXktVOgt74%3D]

    Publisher Full Text OpenURL

  31. Wang D, Xu R, Wang X, Li Y:

    Nanotechnology. 2006, 17:979.

    COI number [1:CAS:528:DC%2BD28XjtV2msL4%3D]; Bibcode number [2006Nanot..17..979W]

    Publisher Full Text OpenURL

  32. Xiang L, Deng XY, Jin Y:

    Scr Mater. 2002, 47:219.

    COI number [1:CAS:528:DC%2BD38XlsFymtLY%3D]

    Publisher Full Text OpenURL

  33. Benito P, Labajos FM, Rives V:

    J Solid State Chem. 2006, 179:3784.

    COI number [1:CAS:528:DC%2BD28Xht1KrtbnL]; Bibcode number [2006JSSCh.179.3784B]

    Publisher Full Text OpenURL

  34. Li X, Xiong Y, Li Z, Xie Y:

    Inorg. Chem. 2006, 45:9493. Publisher Full Text OpenURL

  35. Wu C, Xie Y, Lei L, Hu S, OuYang C:

    Adv Mater. 2006, 18:1727.

    COI number [1:CAS:528:DC%2BD28XntFWiu7Y%3D]

    Publisher Full Text OpenURL

  36. Zhu LP, Xiao HM, Zhang WD, Yang G, Fu SY:

    Cryst Growth Des. 2008, 8:957.

    COI number [1:CAS:528:DC%2BD1cXhvV2mtrk%3D]

    Publisher Full Text OpenURL

  37. Gui Z, Liu J, Wang Z, Song L, Hu Y, Fan W, Chen D:

    J Phys Chem B. 2005, 109:1113.

    COI number [1:CAS:528:DC%2BD2MXjslOn]

    Publisher Full Text OpenURL

  38. Pankove J: Optical Processes in Semiconductors. Prentice-Hall, Englewood Cliffs, NJ; 1971. OpenURL

  39. Varkey AJ, Fort AF:

    Thin Solid Films. 1993, 235:47.

    COI number [1:CAS:528:DyaK2cXms1SqsA%3D%3D]; Bibcode number [1993TSF...235...47V]

    Publisher Full Text OpenURL

  40. Lin Y, Xie T, Cheng B, Geng B, Zhang L:

    Chem Phys Lett. 2003, 380:521.

    COI number [1:CAS:528:DC%2BD3sXotlWrs7c%3D]; Bibcode number [2003CPL...380..521L]

    Publisher Full Text OpenURL