SpringerOpen Newsletter

Receive periodic news and updates relating to SpringerOpen.

Open Access Nano Express

A Simple Method to Synthesize Cadmium Hydroxide Nanobelts

DE Zhang1*, XD Pan1, H Zhu1, SZ Li1, GY Xu1, XB Zhang1, AL Ying1 and ZW Tong12*

Author Affiliations

1 Department of Chemical Engineering, Huaihai Institute of Technology, Lianyungang, 222005, People’s Republic of China

2 SORST, Japan Science and Technology Agency (JST), Tokyo, Japan

For all author emails, please log on.

Nanoscale Research Letters 2008, 3:284-288  doi:10.1007/s11671-008-9150-4

The electronic version of this article is the complete one and can be found online at:


Received:6 May 2008
Accepted:11 July 2008
Published:9 August 2008

© 2008 to the authors

Abstract

Cd(OH)2nanobelts have been synthesized in high yield by a convenient polyol method for the first time. XRD, XPS, FESEM, and TEM were used to characterize the product, which revealed that the product consisted of belt-like crystals about 40 nm in thickness and length up to several hundreds of micrometers. Studies found that the viscosity of the solvent has important influence on the morphology of the final products. The optical absorption spectrum indicates that the Cd(OH)2nanobelts have a direct band gap of 4.45 eV.

Keywords:
Crystal morphology; Nanobelt; Viscosity; Hydrothermal

Introduction

One-dimensional (1D) nanostructures such as wires, rods, belts, and tubes, whose lateral dimensions fall anywhere in the range of 1–100 nm, have become the focus of intensive research, owing to their unique applications in mesoscopic physics and fabrication of nanoscale devices [1-6]. Among one-dimensional (1D) nanostructures, nanobelts (or nanoribbons), a relatively new family of 1D nanostructures with a rectangular cross section, have received increasing attention since the discovery of novel oxide semiconductor nanobelts [4-8]. A variety of functional oxide [3,9] and sulfide [10-17] nanobelts have been successfully fabricated by simple thermal evaporation. The methods used in 1D nanostructure synthesis and hydrothermal processes have emerged as powerful tools for the fabrication of anisotropic nanomaterials with some significant advantages, such as controllable particle size and low-temperature, cost-effective, and less-complicated techniques. Under hydrothermal conditions, many starting materials can undergo quite unexpected reactions, which are often accompanied by the formation of nanoscopic morphologies that are not accessible by classical routes [18]. In recent years, 1D nanomaterials such as Ln(OH)3[19-21], CdWO4[22], MoO3[23], and Dy(OH)3[24] have been successfully synthesized using hydrothermal methods.

Cadmium hydroxide, Cd(OH)2, is a wide band gap semiconductor [25] with a wide range of possible applications including solar cells, photo transistors and diodes, transparent electrodes, sensors, etc. [26,27]. Cadmium hydroxide is also the precursor to prepare cadmium oxide [18]. As a consequence, numerous techniques have been proposed to synthesize nano-sized Cd(OH)2 particles with promising control of properties [25-28]. However, up to now, to our best knowledge, the synthesis of Cd(OH)2 nanobelts by hydrothermal process has not been reported. Herein, we report the preparation of cadmium hydroxide nanobelts by the conventional polyol assisted hydrothermal process.

Materials and Methods

In a typical procedure; CdCl2 · 2H2O (0.2281 g) was dissolved in 32 mL of distilled water, and then NH3 · H2O (25 wt.%, 5 mL) was slowly added into the solution and stirred for about 10 min, and a transparent Cd(NH3)42−solution was formed. Then, the above solution was loaded into a 50-mL Teflon-lined autoclave, which was then filled with 8 mL of glycol. The autoclave was sealed, warmed up at a speed of 3 ºC/min and maintained at 100 ºC for 6 h, and was then cooled to room temperature on standing. The white precipitate was filtered off, washed with absolute ethanol and distilled water for several times, and then dried in vacuum at 40 ºC for 4 h.

X-ray diffraction (XRD) patterns were carried out on a Japan Rigaku D/max rA X-ray diffractometer equipped with graphitemonochromatized high-intensity Cu Ka radiation (λ= 1.541784 Å). The accelerating voltage was set at 50 kV, with 100 mA flux at a scanning rate of 0.06°/s in the 2θ range 10–80°. The X-ray photoelectron spectra (XPS) were collected on an ESCALab MKII X-ray photoelectron spectrometer using nonmonochromatized Mg KR X-ray as the excitation source. The field emission scanning electron microscopy (FE-SEM) images were taken on a JEOL JSM-6700FSEM. The transmission electron microscopy (TEM) images were characterized by Hitachi H-800 transmission electron microscope with a tungsten filament and an accelerating voltage of 200 kV.

Results and Discussion

The XRD pattern (Fig. 1) from the as-synthesized bulk samples reveals the crystal structure and phase purity of the products. All the diffraction peaks can be indexed to the hexagonal Cd(OH)2with cell constantsa = 3.4942,c = 4.7102, which are consistent with the values in the literature (JCPDS 31-0228). The abnormally intensified (100) peak in the XRD pattern also indicates that the belt-like product comprises 1D Cd(OH)2crystals preferentially grown along the [001] direction.

thumbnailFigure 1. Powder XRD patterns of the products

Figure 2 shows the XPS spectra of the as-obtained Cd(OH)2 sample. A survey spectrum shown in Fig. 2a, indicates the presence of Cd and O as well as C from reference. There are no peaks for other impurities, indicating that the as-obtained product is relatively pure. High-resolution spectra are also taken for the Cd 3d region and the O 1s region to determine the valency state and atomic ratio. The binding energies of Cd(3d5/2) and O(1s) were found to be 405.30 and 531.25 eV, respectively. All the above observed binding energy values are in good agreement with the reported data [29,30]. Quantification of the XPS peaks gives the molar ratio of Cd:O as 1:2.02, close to the stoichiometry of Cd(OH)2. This also validated our speculation in XRD study.

thumbnailFigure 2. XPS analysis of the nanobelts

A typical low-magnification FESEM image (Fig. 3a) shows that the as-synthesized products consist of a large quantity of 1D nanostructures with lengths from several tens to several hundreds of micrometers; some of them even have lengths of the order of millimeters. A representative high magnification SEM image (Fig. 3b) of several curved Cd(OH)21D nanostructures reveals that their geometrical shape is belt-like, which is distinct from those of previously reported nanowires, and their thickness is about 30–50 nm.

thumbnailFigure 3. Typical FESEM morphologies of the as-synthesized product. (a) Low-magnification image revealing large quantities of Cd(OH)2nanobelts. (b) High-magnification image of curved nanobelts

TEM and SAED studies of the as-synthesized products provide further insight into the belt-like Cd(OH)2nanostructures. Straight and curved Cd(OH)2nanobelts can be observed in Fig. 4b. The nanobelts are uniform in width and thickness, and their typical widths and thickness are in the range of 60–250 nm and 10–30 nm, respectively. The SAED pattern (inset in Fig. 4b) taken from the straight section of the curved nanobelt demonstrates that this particular nanobelt is a single crystal.

thumbnailFigure 4. TEM images of Cd(OH)2nanobelts. (a) Regular Cd(OH)2 nanobelts. (b) Single curved Cd(OH)2 nanobelt

For the polyol process, glycol was selected as the solvent because of its excellent viscosity, which makes it possible to mix the reagents homogeneously. In the process, glycol can provide reaction conditions adequate to greatly enhance solubility, diffusion, and crystallization, but is still mild to leave molecular building blocks to bring about the formation of the solid-state phase. At reaction temperature, the diffusion of ions in glycol is more rapid than in other polyol, such as glycerine and diethylene glycol; this leads to acceleration in the solubility of starting materials and in the following crystal growth. Both higher viscosity and lower viscosity are not beneficial for getting unique geometrical nanostructures. The concentrations of glycol of about 20–30 vol.%, were found to be favorable for the formation of the Cd(OH)2 nanobelts in high yield. Such viscosity had a good effect on prohibiting aggregation of Cd(OH)2particles and then resulted in a relatively stable suspension. Control reactions at a low concentration of glycol (3 mL) would plate out a large amount of the Cd(OH)2 nanorods (Fig. 5a). At very high concentrations (20 mL glycol), however, only the aggregated particles were observed (Fig. 5b). Different solvents were also tested to reveal the solvent effect. When glycerine was used, nanobelts were not obtained due to the high viscosity of solvent. Usage of other polyol leads to similar results. From the experimental results, we can clearly see that the viscosity is of importance to the structure of the final product. The best solvent to get uniform belt-like pattern is glycol.

thumbnailFigure 5. SEM images of Cd(OH)2 samples using different concentrations of glycol: (a) 3 mL; (b) 20 mL

The optical absorption spectrum of our sample is shown in Fig. 6. Compared to other researcher’s work [26], the absorption edge obviously shifts toward shorter wavelength, i.e., blue shift. The absorption band gap Eg can be determined by the following equation: (αhυ)n= B(hυ − Eg) [31], in which hυ is the photo energy, α is the absorption coefficient, B is a constant relative to the material, and n is either 2 for a direct transition or 1/2 for an indirect transition. The (αhυ)2 ~ hυ curve for the samples shown in Fig. 6 insert reveals that the band gap of the samples is about 4.45 ev, which is larger than the reported value for Cd(OH)2 thin film (Eg = 2.75 eV) [25], but is less than the reported value for nanostrands, which have a constant width of 1.9 nm (Eg = 4.76 eV) [28] due to the quantum size effect [32].

thumbnailFigure 6. Optical absorption spectrum and (αhν)2 ~ hν curve for the Cd(OH)2 nanobelts

Conclusions

In summary, Cd(OH)2nanobelts with a uniform diameter have been successfully prepared in high yield through a rapid polyol process. It was found that the viscosity of the solvent played an important role in determining the morphology. We believe that it should be possible to synthesize other similar patterns by choosing an appropriate solvent. The optical absorption spectrum indicates that the Cd(OH)2nanobelts have a direct band gap of 4.45 eV.

Acknowledgment

This work was supported by a Grant-in-aid for Scientific Research from the Japan Society for the Promotion of Science (JSPS) and the CREST program of the Japan Science and Technology Agency (JST). We are grateful to young and middle aged academic leaders of Jiangsu Province universities’ “blue and green blue project.” We are grateful to the electron microscope and X-ray diffraction facilities of university of science & technology of china for assistance in XRD and SEM measurement.

References

  1. Frank S, Poncharal P, Wang ZL, de Heer WA:

    Science. 1998, 280:1744.

    COI number [1:CAS:528:DyaK1cXjslOhu7g%3D]

    Publisher Full Text OpenURL

  2. Duan XF, Liber CM:

    J. Am. Chem. Soc.. 2000, 122:188.

    COI number [1:CAS:528:DyaK1MXnvF2qt7w%3D]

    Publisher Full Text OpenURL

  3. Pan ZW, Dai ZR, Wang ZL:

    Science. 1947, 291:2001. OpenURL

  4. Dong LH, Chu Y, Liu Y, Li MY, Yang FY, Li LL:

    J. Coll. Inter. Sci.. 2006, 301:503.

    COI number [1:CAS:528:DC%2BD28XotVars7Y%3D]

    Publisher Full Text OpenURL

  5. Rakovicha AY, Stockhausena V, Sushaa AS, Sapraa S, Rogach AL:

    Colloids Surf. A. 2008, 317:737. Publisher Full Text OpenURL

  6. Zhou ZZ, Deng YL:

    J. Coll. Inter. Sci.. 2007, 316:183.

    COI number [1:CAS:528:DC%2BD2sXhtFGrtrzO]

    Publisher Full Text OpenURL

  7. Wu YY, Yan HQ, Huang M, Messer B, Song JH, Yang PD:

    Chem Eur. J.. 2002, 8:1261. OpenURL

  8. Dai ZR, Pan ZW, Wang ZL:

    Adv. Funct. Mater.. 2003, 13:9. Publisher Full Text OpenURL

  9. Ma C, Moore D, Li J, Wang ZL:

    Adv. Mater.. 2003, 15:228.

    COI number [1:CAS:528:DC%2BD3sXhs1ShtL0%3D]

    Publisher Full Text OpenURL

  10. Jiang Y, Meng XM, Liu J, Xie Z, Lee Y, Lee ST:

    Adv. Mater.. 2003, 15:323.

    COI number [1:CAS:528:DC%2BD3sXitlOjsrk%3D]

    Publisher Full Text OpenURL

  11. Liddell CM, Summers CJ:

    J. Coll. Inter. Sci.. 2004, 274:103.

    COI number [1:CAS:528:DC%2BD2cXjsFOgs70%3D]

    Publisher Full Text OpenURL

  12. Jong T, Parry DL:

    J. Coll. Inter. Sci.. 2004, 275:61.

    COI number [1:CAS:528:DC%2BD2cXktFKktrs%3D]

    Publisher Full Text OpenURL

  13. Yekeler M, Yekeler H:

    J. Coll. Inter. Sci.. 2005, 284:694.

    COI number [1:CAS:528:DC%2BD2MXisVWktrs%3D]

    Publisher Full Text OpenURL

  14. Borse PH, Vogel W, Kulkarni SK:

    J. Coll. Inter. Sci.. 2006, 293:437.

    COI number [1:CAS:528:DC%2BD2MXht1aht73E]

    Publisher Full Text OpenURL

  15. Chiriţă P, Descostes M:

    J. Coll. Inter. Sci.. 2006, 294:376. Publisher Full Text OpenURL

  16. Tang B, Zhuo LH, Ge JC, Niu JY, Shi ZQ:

    Inorg. Chem.. 2005, 44:2568.

    COI number [1:CAS:528:DC%2BD2MXisVSgsbs%3D]

    Publisher Full Text OpenURL

  17. Peng ZA, Peng X:

    J. Am. Chem. Soc.. 2001, 123:1389.

    COI number [1:CAS:528:DC%2BD3MXmslSgtA%3D%3D]

    Publisher Full Text OpenURL

  18. Peng ZA, Peng X:

    J. Am. Chem. Soc.. 2002, 124:3343.

    COI number [1:CAS:528:DC%2BD38Xhslegtro%3D]

    Publisher Full Text OpenURL

  19. Wang X, Li YD:

    Chem. Eur. J.. 2003, 9:5627.

    COI number [1:CAS:528:DC%2BD3sXps1OjtLk%3D]

    Publisher Full Text OpenURL

  20. Liao HW, Wang YF, Liu XM, Li YD, Qian YT:

    Chem. Mater.. 2000, 12:2819.

    COI number [1:CAS:528:DC%2BD3cXmsFGjtLw%3D]

    Publisher Full Text OpenURL

  21. Patzke GR, Michailovski A, Krumeich F, Nesper R, Grunwaldt JD, Baiker A:

    Chem. Mater.. 2004, 16:1126.

    COI number [1:CAS:528:DC%2BD2cXhs1Cmtrk%3D]

    Publisher Full Text OpenURL

  22. Xu AW, Fang YP, You LP, Liu HQ:

    J. Am. Chem. Soc.. 2003, 125:1494.

    COI number [1:CAS:528:DC%2BD3sXksFersg%3D%3D]

    Publisher Full Text OpenURL

  23. Zhang H, Ma XY, Ji YJ, Xu J, Yang DR:

    Mater. Lett.. 2005, 59:56.

    COI number [1:CAS:528:DC%2BD2cXpsFSmt7k%3D]

    Publisher Full Text OpenURL

  24. Ristic M, Popovic S, Music S:

    Mater. Lett.. 2004, 58:2494.

    COI number [1:CAS:528:DC%2BD2cXkvVWmtrw%3D]

    Publisher Full Text OpenURL

  25. Mane RS, Han S-H:

    Electrochem. Commun.. 2005, 7:205.

    COI number [1:CAS:528:DC%2BD2MXmvF2kug%3D%3D]

    Publisher Full Text OpenURL

  26. Luo YH, Huang JG, Ichinose I:

    J. Am. Chem. Soc.. 2005, 9:8297. OpenURL

  27. Hammaond JS, Gaarenstroom SW, Winograd N:

    Anal. Chem.. 1975, 47:2194. OpenURL

  28. Pankove JI: Optical processes in semiconductors. Prentice-Hall, Englewood Cliffs, NJ; 1971. OpenURL